MC908JL16CFJE Freescale Semiconductor, MC908JL16CFJE Datasheet - Page 209

• Manufacturer Part Number: MC908JL16CFJE
• Description: IC MCU 16K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908JL16CFJE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI
• Peripherals: LED, LVD, POR, PWM
• Number Of I /o: 26
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: HC08JL
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 26
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908JL16E, M68CBL05CE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Controller Family/series: HC08
• No. Of I/o's: 26
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• For Use With: DEMO908JL16E - BOARD DEMO FOR MC908JL16
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

17.9 3-V Control Timing
Freescale Semiconductor
Low-voltage inhibit, trip falling voltage
Low-voltage inhibit, trip rising voltage
Low-voltage inhibit reset/recovery hysteresis
Internal operating frequency
RST input pulse width low
IRQ input pulse width low
TIM2 external clock input
1. V
2. Typical values reflect average measurements at midpoint of voltage range, 25 °C only.
3. Run (operating) I
4. Wait I
5. Stop I
6. Maximum is highest voltage that POR is guaranteed.
7. If minimum V
8. R
1. V
2. Some modules may require a minimum frequency greater than dc for proper operation; see appropriate table for this infor-
3. Minimum pulse width reset is guaranteed to be recognized. It is possible for a smaller pulse width to cause a reset.
Less than 100 pF on all outputs. C
run I
100 pF on all outputs. C
V
noted.
mation.
DD
DD
DD
PU
= 2.7 to 3.3 Vdc, V
DD
= 2.7 to 3.3 Vdc, V
is measured at V
is reached.
DD
DD
. Measured with all modules enabled.
measured using external square wave clock source (f
measured with OSC1 grounded; no port pins sourcing current.
DD
is not reached before the internal POR reset is released, RST must be driven low externally until minimum
DD
Characteristic
measured using external square wave clock source (f
DD
(3)
Characteristic
(3)
SS
SS
L
= 5.0V.
(2)
= 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait I
= 0 Vdc, T
= 0 Vdc, T
Table 17-7. DC Electrical Characteristics (3V)
(1)
L
A
A
= 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects
(1)
= T
= T
Table 17-8. Control Timing (3V)
MC68HC908JL16 Data Sheet, Rev. 1.1
L
L
to T
to T
H
H
; timing shown with respect to 20% V
, unless otherwise noted.
Symbol
V
OP
V
V
TRIPR
TRIPF
HYS
= 4MHz). All inputs 0.2V from rail. No dc loads. Less than
Symbol
f
T2CLK
OP
t
f
t
IRL
OP
IIL
= 4MHz). All inputs 0.2V from rail. No dc loads.
2.475
2.40
Min
—
DD
Min
1.5
1.5
—
—
and 70% V
Typ
2.625
2.55
75
(2)
Max
DD
—
—
4
2
3-V Control Timing
, unless otherwise
2.775
Max
2.70
—
MHz
MHz
Unit
µs
µs
DD
Unit
mV
.
V
V
209