C8051F312-GQ Silicon Laboratories Inc, C8051F312-GQ Datasheet - Page 164
![IC 8051 MCU 8K FLASH 32LQFP](/photos/12/16/121654/c8051f312-gq_sml.jpg)
C8051F312-GQ
Manufacturer Part Number
C8051F312-GQ
Description
IC 8051 MCU 8K FLASH 32LQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F31xr
Specifications of C8051F312-GQ
Program Memory Type
FLASH
Program Memory Size
8KB (8K x 8)
Package / Case
32-LQFP
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
POR, PWM, Temp Sensor, WDT
Number Of I /o
29
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 3.6 V
Data Converters
A/D 21x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Processor Series
C8051F3x
Core
8051
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C, SMBus, SPI, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
29
Number Of Timers
4 bit
Operating Supply Voltage
2.7 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
C8051F310DK
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 21 Channel
No. Of I/o's
29
Ram Memory Size
1280Byte
Cpu Speed
25MHz
No. Of Timers
4
Rohs Compliant
Yes
Package
32LQFP
Device Core
8051
Family Name
C8051F31x
Maximum Speed
25 MHz
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
336-1445 - ADAPTER PROGRAM TOOLSTICK F310
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
336-1255
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F312-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F312-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
C8051F310/1/2/3/4/5/6/7
15.1. Enhanced Baud Rate Generation
The UART0 baud rate is generated by Timer 1 in 8-bit auto-reload mode. The TX clock is generated by
TL1; the RX clock is generated by a copy of TL1 (shown as RX Timer in Figure 15.2), which is not user-
accessible. Both TX and RX Timer overflows are divided by two to generate the TX and RX baud rates.
The RX Timer runs when Timer 1 is enabled, and uses the same reload value (TH1). However, an
RX Timer reload is forced when a START condition is detected on the RX pin. This allows a receive to
begin any time a START is detected, independent of the TX Timer state.
Timer 1 should be configured for Mode 2, 8-bit auto-reload (see
ter/Timer with Auto-Reload” on page
occur at two times the desired UART baud rate frequency. Note that Timer 1 may be clocked by one of six
sources: SYSCLK, SYSCLK / 4, SYSCLK / 12, SYSCLK / 48, the external oscillator clock / 8, or an exter-
nal input T1. For any given Timer 1 clock source, the UART0 baud rate is determined by Equation 15.1.
Where T1
value). Timer 1 clock frequency is selected as described in
reference for typical baud rates and system clock frequencies is given in Table 15.1 through Table 15.6.
Note that the internal oscillator may still generate the system clock when the external oscillator is driving
Timer 1.
164
CLK
is the frequency of the clock supplied to Timer 1, and T1H is the high byte of Timer 1 (reload
Detected
Start
Figure 15.2. UART0 Baud Rate Logic
RX Timer
Equation 15.1. UART0 Baud Rate
UartBaudRate
Timer 1
TH1
TL1
189). The Timer 1 reload value should be set so that overflows will
Overflow
Overflow
Rev. 1.7
=
------------------------------ -
256 T1H
T1
–
Section “17. Timers” on page
CLK
2
2
Section “17.1.3. Mode 2: 8-bit Coun-
UART
1
-- -
2
RX Clock
TX Clock
187. A quick