C8051F351-GM Silicon Laboratories Inc, C8051F351-GM Datasheet - Page 163

• Manufacturer Part Number: C8051F351-GM
• Description: IC 8051 MCU 8K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F35xr

Specifications of C8051F351-GM

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 28-MLP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 17
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x24b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F350DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 24-bit
• On-chip Dac: 2-ch x 8-bit
• Package: 28QFN
• Device Core: 8051
• Family Name: C8051F35x
• Maximum Speed: 50 MHz
• Data Rom Size: 128 B
• Height: 0.88 mm
• Length: 5 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1083 - DEV KIT FOR F350/351/352/353
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1271

19.5. SMBus Transfer Modes
The SMBus interface may be configured to operate as master and/or slave. At any particular time, it will be
operating in one of the following four modes: Master Transmitter, Master Receiver, Slave Transmitter, or
Slave Receiver. The SMBus interface enters Master Mode any time a START is generated, and remains in
Master Mode until it loses an arbitration or generates a STOP. An SMBus interrupt is generated at the end
of all SMBus byte frames; however, note that the interrupt is generated before the ACK cycle when operat-
ing as a receiver, and after the ACK cycle when operating as a transmitter.
19.5.1. Master Transmitter Mode
Serial data is transmitted on SDA while the serial clock is output on SCL. The SMBus interface generates
the START condition and transmits the first byte containing the address of the target slave and the data
direction bit. In this case the data direction bit (R/W) will be logic 0 (WRITE). The master then transmits
one or more bytes of serial data. After each byte is transmitted, an acknowledge bit is generated by the
slave. The transfer is ended when the STO bit is set and a STOP is generated. Note that the interface will
switch to Master Receiver Mode if SMB0DAT is not written following a Master Transmitter interrupt.
Figure 19.5 shows a typical Master Transmitter sequence. Two transmit data bytes are shown, though any
number of bytes may be transmitted. Notice that the ‘data byte transferred’ interrupts occur after the ACK
cycle in this mode.
Figure 19.5. Typical Master Transmitter Sequence
Interrupt
S
Received by SMBus
Interface
Transmitted by
SMBus Interface
SLA
W
Interrupt
A
Data Byte
Rev. 1.1
Interrupt
A
S = START
P = STOP
A = ACK
W = WRITE
SLA = Slave Address
Data Byte
C8051F350/1/2/3
Interrupt
A
P
163