MC9S12GC64MFAE Freescale Semiconductor, MC9S12GC64MFAE Datasheet - Page 341

• Manufacturer Part Number: MC9S12GC64MFAE
• Description: IC MCU 64K FLASH 25MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12GC64MFAE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 31
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 48-LQFP
• Processor Series: S12GC
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 4 KB
• Interface Type: CAN/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 31
• Number Of Timers: 8
• Operating Supply Voltage: 3.3 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912C32EE, M68DKIT912C32SLK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

10.4.7.6
Interrupts are directly associated with one or more status flags in either the
Receiver Flag Register
(CANTFLG).” Interrupts are pending as long as one of the corresponding flags is set. The flags in
CANRFLG and CANTFLG must be reset within the interrupt handler to handshake the interrupt. The flags
are reset by writing a 1 to the corresponding bit position. A flag cannot be cleared if the respective
condition prevails.
10.4.7.7
The MSCAN can recover from stop or wait via the wake-up interrupt. This interrupt can only occur if the
MSCAN was in sleep mode (SLPRQ = 1 and SLPAK = 1) before entering power down mode, the wake-
up option is enabled (WUPE = 1), and the wake-up interrupt is enabled (WUPIE = 1).
10.5
10.5.1
The procedure to initially start up the MSCAN module out of reset is as follows:
If the configuration of registers which are writable in initialization mode needs to be changed only when
the MSCAN module is in normal mode:
Freescale Semiconductor
1. Assert CANE
2. Write to the configuration registers in initialization mode
3. Clear INITRQ to leave initialization mode and enter normal mode
1. Bring the module into sleep mode by setting SLPRQ and awaiting SLPAK to assert after the CAN
2. Enter initialization mode: assert INITRQ and await INITAK
3. Write to the configuration registers in initialization mode
4. Clear INITRQ to leave initialization mode and continue in normal mode
“MSCAN Receiver Flag Register
Interrupt Enable Register
bus becomes idle.
Initialization/Application Information
MSCAN initialization
Interrupt Acknowledge
Recovery from Stop or Wait
It must be guaranteed that the CPU clears only the bit causing the current
interrupt. For this reason, bit manipulation instructions (BSET) must not be
used to clear interrupt flags. These instructions may cause accidental
clearing of interrupt flags which are set after entering the current interrupt
service routine.
(CANRFLG)” or the
(CANRIER)”).
MC9S12C-Family / MC9S12GC-Family
(CANRFLG)” and
Section 10.3.2.7, “MSCAN Transmitter Flag Register
Chapter 10 Freescale’s Scalable Controller Area Network (S12MSCANV2)
Rev 01.24
NOTE
Section 10.3.2.6, “MSCAN Receiver
Section 10.3.2.5, “MSCAN
341