PIC16LC620A-04/P Microchip Technology, PIC16LC620A-04/P Datasheet - Page 30

• Manufacturer Part Number: PIC16LC620A-04/P
• Description: IC MCU OTP 512X14 COMP 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16LC620A-04/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 13
• Program Memory Size: 896B (512 x 14)
• Program Memory Type: OTP
• Ram Size: 96 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Processor Series: PIC16LC
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 96 B
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 8
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC16LC620A-04/PR; PIC16LC620A-04/PR

PIC16C62X
5.2
PORTB is an 8-bit wide, bi-directional port. The
corresponding data direction register is TRISB. A '1' in
the TRISB register puts the corresponding output driver
in a High Impedance mode. A '0' in the TRISB register
puts the contents of the output latch on the selected
pin(s).
Reading PORTB register reads the status of the pins,
whereas writing to it will write to the port latch. All write
operations are read-modify-write operations. So a write
to a port implies that the port pins are first read, then
this value is modified and written to the port data latch.
Each of the PORTB pins has a weak internal pull-up
(≈200 µA typical). A single control bit can turn on all the
pull-ups. This is done by clearing the RBPU
(OPTION<7>) bit. The weak pull-up is automatically
turned off when the port pin is configured as an output.
The pull-ups are disabled on Power-on Reset.
Four of PORTB’s pins, RB<7:4>, have an interrupt on
change feature. Only pins configured as inputs can
cause this interrupt to occur (e.g., any RB<7:4> pin
configured as an output is excluded from the interrupt
on change comparison). The input pins (of RB<7:4>)
are compared with the old value latched on the last
read of PORTB. The “mismatch” outputs of RB<7:4>
are OR’ed together to generate the RBIF interrupt (flag
latched in INTCON<0>).
FIGURE 5-5:
DS30235J-page 28
Set RBIF
Note 1: TRISB = 1 enables weak pull-up if RBPU = '0'
RB<7:6> in Serial Programming mode
Data Bus
WR TRISB
WR PORTB
RBPU
From other
RB<7:4> pins
(1)
(OPTION<7>).
PORTB and TRISB Registers
RD TRISB
RD PORTB
Data Latch
TRIS Latch
D
D
CK
CK
BLOCK DIAGRAM OF
RB<7:4> PINS
Q
Q
Q
Q
Q
Q
Latch
EN
EN
D
D
TTL
Input
Buffer
RD PORTB
V
P
DD
weak
pull-up
V
ST
Buffer
SS
V
CC
I/O
pin
This interrupt can wake the device from SLEEP. The
user, in the interrupt service routine, can clear the
interrupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit RBIF to be cleared.
This interrupt on mismatch feature, together with
software configurable pull-ups on these four pins allow
easy interface to a key pad and make it possible for
wake-up on key-depression. (See AN552, “Implement-
ing Wake-Up on Key Strokes.)
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt on change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
FIGURE 5-6:
Data Bus
WR TRISB
WR PORTB
RBPU
RB0/INT
Note:
Note 1: TRISB = 1 enables weak pull-up if RBPU = '0'
Any read or write of PORTB. This will end the
mismatch condition.
Clear flag bit RBIF.
(1)
(OPTION<7>).
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RBIF inter-
rupt flag may not get set.
RD PORTB
RD TRISB
Data Latch
D
D
CK
CK
ST
Buffer
BLOCK DIAGRAM OF
RB<3:0> PINS
 2003 Microchip Technology Inc.
Q
Q
Q
Q
Q
EN
TTL
Input
Buffer
D
RD PORTB
V
P
DD
V
weak
pull-up
SS
V
CC
I/O
pin