C8051F341-GQ Silicon Laboratories Inc, C8051F341-GQ Datasheet - Page 160

• Manufacturer Part Number: C8051F341-GQ
• Description: IC 8051 MCU FLASH 32K 48TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F34xr

Specifications of C8051F341-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-TQFP, 48-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 40
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 20x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 3.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 5.25 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-F34X, KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F340DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 17-ch x 10-bit
• No. Of I/o's: 40
• Ram Memory Size: 2304Byte
• Cpu Speed: 48MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Package: 48TQFP
• Device Core: 8051
• Family Name: C8051F34x
• Maximum Speed: 48 MHz
• Data Rom Size: 128 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 17
• Height: 1 mm
• Length: 7 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Width: 7 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1748 - ADAPTER TOOLSTICK FOR C8051F34X770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1452 - ADAPTER PROGRAM TOOLSTICK F340
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1299

C8051F340/1/2/3/4/5/6/7/8/9/A/B/C/D
16.1. Endpoint Addressing
A total of eight endpoint pipes are available. The control endpoint (Endpoint0) always functions as a
bi-directional IN/OUT endpoint. The other endpoints are implemented as three pairs of IN/OUT endpoint
pipes:
16.2. USB Transceiver
The USB Transceiver is configured via the USB0XCN register shown in SFR Definition 16.1. This configu-
ration includes Transceiver enable/disable, pull-up resistor enable/disable, and device speed selection
(Full or Low Speed). When bit SPEED = ‘1’, USB0 operates as a Full Speed USB function, and the on-chip
pull-up resistor (if enabled) appears on the D+ pin. When bit SPEED = ‘0’, USB0 operates as a Low Speed
USB function, and the on-chip pull-up resistor (if enabled) appears on the D- pin. Bits4-0 of register
USB0XCN can be used for Transceiver testing as described in SFR Definition 16.1. The pull-up resistor is
enabled only when VBUS is present (see
VBUS detection).
Important Note: The USB clock should be active before the Transceiver is enabled.
160
Endpoint0
Endpoint1
Endpoint2
Endpoint3
Endpoint
Table 16.1. Endpoint Addressing Scheme
Associated Pipes
Endpoint0 OUT
Endpoint1 OUT
Endpoint2 OUT
Endpoint3 OUT
Endpoint0 IN
Endpoint1 IN
Endpoint2 IN
Endpoint3 IN
Section “8.2. VBUS Detection” on page 69
Rev. 1.3
USB Protocol Address
0x00
0x00
0x81
0x01
0x82
0x02
0x83
0x03
for details on