PIC16F684-E/SL Microchip Technology, PIC16F684-E/SL Datasheet - Page 36
![IC PIC MCU FLASH 2KX14 14SOIC](/photos/6/59/65933/150-14-soic_sml.jpg)
PIC16F684-E/SL
Manufacturer Part Number
PIC16F684-E/SL
Description
IC PIC MCU FLASH 2KX14 14SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F688T-ISL.pdf
(688 pages)
3.PIC16F684-ISL.pdf
(4 pages)
4.PIC16F684-ISL.pdf
(192 pages)
5.PIC16F684-ISL.pdf
(6 pages)
6.PIC16F684-IST.pdf
(164 pages)
Specifications of PIC16F684-E/SL
Program Memory Type
FLASH
Program Memory Size
3.5KB (2K x 14)
Package / Case
14-SOIC (3.9mm Width), 14-SOL
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
12
Eeprom Size
256 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Processor Series
PIC16F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
128 B
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
12
Number Of Timers
3
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
Minimum Operating Temperature
- 40 C
On-chip Adc
8-ch x 10-bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Connectivity
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
PIC16F684
4.2.4
The Ultra Low-Power Wake-Up (ULPWU) on RA0
allows a slow falling voltage to generate an
interrupt-on-change on RA0 without excess current
consumption. The mode is selected by setting the
ULPWUE bit of the PCON register. This enables a small
current sink which can be used to discharge a capacitor
on RA0.
To use this feature, the RA0 pin is first configured to output
‘1’ to charge the capacitor. Then interrupt-on-change for
RA0 is enabled, and RA0 is configured as an input. The
ULPWUE bit is set to begin the discharge and a SLEEP
instruction is performed. When the voltage on RA0 drops
below V
instruction. If the GIE bit of the INTCON register is set, the
device will call the interrupt service routine (0004h). See
Section 4.2.3
Section 12.4.3 “PORTA Interrupt-on-Change” for
more information.
This feature provides a low-power technique for
periodically waking up the device from Sleep. The
time-out is dependent on the discharge time of the RC
circuit on RA0. See Example 4-2 for initializing the Ultra
Low-Power Wake-Up module.
The series resistor provides overcurrent protection for
the RA0 pin and can allow for software calibration of
the time-out (see Figure 4-1). A timer can be used to
measure the charge time and discharge time of the
capacitor. The charge time can then be adjusted to
provide the desired interrupt delay. This technique will
compensate for the affects of temperature, voltage and
component accuracy. The Ultra Low-Power Wake-Up
peripheral can also be configured as a simple
Programmable Low Voltage Detect or temperature
sensor.
DS41202F-page 34
IL
, the device will wake-up and execute the next
ULTRA LOW-POWER WAKE-UP
“Interrupt-on-Change”
and
EXAMPLE 4-2:
BANKSEL CMCON0
MOVLW
MOVWF
BANKSEL ANSEL
BCF
BCF
BANKSEL PORTA
BSF
CALL
BANKSEL PCON
BSF
BSF
BSF
MOVLW
MOVWF
SLEEP
Note:
H’7’
CMCON0
ANSEL,0
TRISA,0
PORTA,0
CapDelay
PCON,ULPWUE ;Enable ULP Wake-up
IOCA,0
TRISA,0
B’10001000’ ;Enable interrupt
INTCON
For more information, refer to AN879,
“Using the Microchip Ultra Low-Power
Wake-Up
(DS00879).
ULTRA LOW-POWER
WAKE-UP INITIALIZATION
© 2007 Microchip Technology Inc.
Module”
;
;Turn off
;comparators
;
;RA0 to digital I/O
;Output high to
;
;charge capacitor
;
;
;Select RA0 IOC
;RA0 to input
; and clear flag
;Wait for IOC
Application
Note