ATTINY84-20MUR Atmel, ATTINY84-20MUR Datasheet - Page 20

• Manufacturer Part Number: ATTINY84-20MUR
• Description: MCU AVR 8KB FLASH 20MHZ 20QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY84-20MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 12
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

5.4
5.4.1
5.5
5.5.1
20
I/O Memory
Register Description
ATtiny24/44/84
General Purpose I/O Registers
EEARH – EEPROM Address Register
be used. If a reset occurs while a write operation is in progress, the write operation will be com-
pleted provided that the power supply voltage is sufficient.
The I/O space definition of the ATtiny24/44/84 is shown in
All ATtiny24/44/84 I/Os and peripherals are placed in the I/O space. All I/O locations may be
accessed by the LD/LDS/LDD and ST/STS/STD instructions, transferring data between the 32
general purpose working registers and the I/O space. I/O Registers within the address range
0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these registers, the
value of single bits can be checked by using the SBIS and SBIC instructions. See the instruction
set section for more details. When using the I/O specific commands IN and OUT, the I/O
addresses 0x00 - 0x3F must be used. When addressing I/O Registers as data space using LD
and ST instructions, 0x20 must be added to these addresses.
For compatibility with future devices, reserved bits should be written to zero if accessed.
Reserved I/O memory addresses should never be written.
Some of the Status Flags are cleared by writing a logical one to them. Note that CBI and SBI
instructions will only operate on the specified bit, and can therefore be used on registers contain-
ing such Status Flags. The CBI and SBI instructions work with registers 0x00 to 0x1F only.
The I/O and Peripherals Control Registers are explained in later sections.
The ATtiny24/44/84 contains three General Purpose I/O Registers. These registers can be used
for storing any information, and they are particularly useful for storing global variables and status
flags. General Purpose I/O Registers within the address range 0x00 - 0x1F are directly bit-
accessible using the SBI, CBI, SBIS, and SBIC instructions.
• Bits 7:1 – Res: Reserved Bits
These bits are reserved in the ATtiny24/44/84 and will always read as zero.
• Bit 0 – EEAR8: EEPROM Address
This is the most significant EEPROM address bit of ATtiny84. In devices with less EEPROM, i.e.
ATtiny24/ATtiny44, this bit is reserved and will always read zero. The initial value of the
EEPROM Address Register (EEAR) is undefined and a proper value must therefore be written
before the EEPROM is accessed.
Bit
0x1F (0x3F)
Read/Write
Initial Value
R
7
–
0
R
6
–
0
5
–
R
0
R
4
–
0
R
3
–
0
“Register Summary” on page
R
2
–
0
R
1
–
0
EEAR8
R/W
X/0
0
8006K–AVR–10/10
EEARH
213.