ATMEGA8L-8AUR Atmel, ATMEGA8L-8AUR Datasheet - Page 181
![no-image](/images/manufacturer_photos/0/0/78/atmel_sml.jpg)
ATMEGA8L-8AUR
Manufacturer Part Number
ATMEGA8L-8AUR
Description
MCU AVR 8KB FLASH 8MHZ 32TQFP
Manufacturer
Atmel
Series
AVR® ATmegar
Datasheet
1.ATMEGA8L-8MU.pdf
(302 pages)
Specifications of ATMEGA8L-8AUR
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
23
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Package
32TQFP
Device Core
AVR
Family Name
ATmega
Maximum Speed
8 MHz
Operating Supply Voltage
3.3|5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
23
Interface Type
SPI/TWI/USART
On-chip Adc
8-chx10-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA8L-8AUR
Manufacturer:
Atmel
Quantity:
3 915
- Current page: 181 of 302
- Download datasheet (6Mb)
Slave Transmitter
Mode
2486Z–AVR–02/11
In the Slave Transmitter mode, a number of data bytes are transmitted to a Master Receiver
(see
zero or are masked to zero.
Figure 84. Data Transfer in Slave Transmitter Mode
To initiate the Slave Transmitter mode, TWAR and TWCR must be initialized as follows:
The upper seven bits are the address to which the Two-wire Serial Interface will respond when
addressed by a Master. If the LSB is set, the TWI will respond to the general call address (0x00),
otherwise it will ignore the general call address.
TWEN must be written to one to enable the TWI. The TWEA bit must be written to one to enable
the acknowledgement of the device’s own slave address or the general call address. TWSTA
and TWSTO must be written to zero.
When TWAR and TWCR have been initialized, the TWI waits until it is addressed by its own
slave address (or the general call address if enabled) followed by the data direction bit. If the
direction bit is “1” (read), the TWI will operate in ST mode, otherwise SR mode is entered. After
its own slave address and the write bit have been received, the TWINT Flag is set and a valid
status code can be read from TWSR. The status code is used to determine the appropriate soft-
ware action. The appropriate action to be taken for each status code is detailed in
page
in the Master mode (see state 0xB0).
If the TWEA bit is written to zero during a transfer, the TWI will transmit the last byte of the trans-
fer. State 0xC0 or state 0xC8 will be entered, depending on whether the Master Receiver
transmits a NACK or ACK after the final byte. The TWI is switched to the not addressed Slave
mode, and will ignore the Master if it continues the transfer. Thus the Master Receiver receives
all “1” as serial data. State 0xC8 is entered if the Master demands additional data bytes (by
transmitting ACK), even though the Slave has transmitted the last byte (TWEA zero and expect-
ing NACK from the Master).
While TWEA is zero, the TWI does not respond to its own slave address. However, the Two-wire
Serial Bus is still monitored and address recognition may resume at any time by setting TWEA.
This implies that the TWEA bit may be used to temporarily isolate the TWI from the Two-wire
Serial Bus.
TWAR
value
TWCR
value
Figure
182. The Slave Transmitter mode may also be entered if arbitration is lost while the TWI is
SDA
SCL
84). All the status codes mentioned in this section assume that the prescaler bits are
TWINT
TWA6
0
TRANSMITTER
Device 1
SLAVE
TWA5
TWEA
1
Device 2
RECEIVER
MASTER
TWSTA
TWA4
Device’s Own Slave Address
0
Device 3
TWSTO
TWA3
0
........
TWWC
TWA2
0
Device n
TWA1
TWEN
V
1
CC
R1
TWA0
ATmega8(L)
–
0
R2
TWGCE
TWIE
X
Table 69 on
181
Related parts for ATMEGA8L-8AUR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATMEGA8L](/images/no-image3.png)
Part Number:
Description:
8-bit AVR with 8K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
![ATMEGA8L-8MU](/photos/12/13/121317/atmega8l-8mu_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 8MHZ 3V 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8PU](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K 8MHZ 3V 28DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8AC](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K LV 8MHZ COM 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8AI](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K LV 8MHZ IND 32TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8PC](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K LV 8MHZ COM 28-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8PI](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K LV 8MHZ IND 28-DIP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8MC](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K LV 8MHZ COM 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8MI](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC AVR MCU 8K LV 8MHZ IND 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8MUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 8KB FLASH 8MHZ 32QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8AJ](/photos/6/91/69154/313-32-tqfp_tmb.jpg)
Part Number:
Description:
IC MCU AVR 8K 5V 8MHZ 32-TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8MJ](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
IC MCU AVR 8K 5V 8MHZ 32-QFN
Manufacturer:
Atmel
Datasheet:
![ATMEGA8L-8PJ](/photos/7/21/72189/453-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU AVR 8K 5V 8MHZ 28-DIP
Manufacturer:
Atmel
Datasheet: