PIC16LF1936-I/SS Microchip Technology, PIC16LF1936-I/SS Datasheet - Page 131

• Manufacturer Part Number: PIC16LF1936-I/SS
• Description: IC PIC MCU FLASH 512KX14 28-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF1936-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 28-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: EUSART, MI2C, SPI
• Maximum Clock Frequency: 32 KHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 14 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

12.2
PORTA is a 8-bit wide, bidirectional port. The
corresponding data direction register is TRISA
(Register 12-3). Setting a TRISA bit (= 1) will make the
corresponding PORTA pin an input (i.e., disable the
output driver). Clearing a TRISA bit (= 0) will make the
corresponding PORTA pin an output (i.e., enables
output driver and puts the contents of the output latch
on the selected pin). Example 12-1 shows how to
initialize PORTA.
Reading the PORTA register (Register 12-2) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then
written to the PORT data latch (LATA).
The TRISA register (Register 12-3) controls the
PORTA pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits
in the TRISA register are maintained set when using
them as analog inputs. I/O pins configured as analog
input always read ‘0’.
12.2.1
The ANSELA register (Register 12-5) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELA bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELA bits has no affect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
EXAMPLE 12-1:
 2009 Microchip Technology Inc.
BANKSEL
CLRF
BANKSEL
CLRF
BANKSEL
CLRF
BANKSEL
MOVLW
MOVWF
Note:
PORTA Registers
ANSELA REGISTER
PORTA
PORTA
LATA
LATA
ANSELA
ANSELA
TRISA
B'11110000' ;Set RA<7:4> as inputs
TRISA
The ANSELA register must be initialized to
configure an analog channel as a digital
input. Pins configured as analog inputs will
read ‘0’.
INITIALIZING PORTA
;
;Init PORTA
;Data Latch
;
;
;digital I/O
;
;and set RA<3:0> as
;outputs
Preliminary
12.2.2
Each PORTA pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are briefly described here. For additional information,
refer to the appropriate section in this data sheet.
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the lowest number in
the following lists.
Analog input functions, such as ADC, comparator and
CapSense inputs, are not shown in the priority lists.
These inputs are active when the I/O pin is set for
Analog mode using the ANSELx registers. Digital
output functions may control the pin when it is in Analog
mode with the priority shown below.
RA0
1.
2.
3.
4.
5.
RA1
1.
2.
RA2
1.
2.
3.
RA3
1.
2.
3.
RA4
1.
2.
3.
4.
5.
RA5
1.
2.
3.
4.
5.
RA6
1.
2.
3.
4.
5.
RA7
1.
2.
3.
PIC16F193X/LF193X
V
SEG12 (LCD)
SRNQ (SR Latch)
C2OUT (Comparator)
RA0
SEG7 (LCD)
RA1
COM2 (LCD)
DACOUT (DAC)
RA2
COM3 (LCD), 28-pin only
SEG15 (LCD)
RA3
SEG4 (LCD)
SRQ (SR Latch)
C1OUT (Comparator)
CCP5 (CCP), 28-pin only
RA4
V
SEG5 (LCD)
SRNQ (SR Latch)
C2OUT (Comparator)
RA5
V
OSC2 (enabled by Configuration Word)
CLKOUT (enabled by Configuration Word)
SEG1 (LCD)
RA6
OSC1/CLKIN (enabled by Configuration Word)
SEG2 (LCD)
RA7
CAP
CAP
CAP
(enabled by Configuration Word)
(enabled by Configuration Word)
(enabled by Configuration Word)
PORTA FUNCTIONS AND OUTPUT
PRIORITIES
DS41364D-page 131