PIC16F883-I/ML Microchip Technology, PIC16F883-I/ML Datasheet - Page 14

• Manufacturer Part Number: PIC16F883-I/ML
• Description: IC PIC MCU FLASH 4KX14 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F883-I/ML

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 24
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: MSSP, EUSART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM164120-3
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Package: 28QFN EP
• Device Core: PIC
• Family Name: PIC16
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MCP1631RD-MCC2 - REFERENCE DESIGN MCP1631HVXLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / Rohs Status: Details

PIC16F88X
3.2.6.1
The Load Configuration command is used to access
the Configuration Words (0x2007-0x2008) and user ID
(0x2000-0x2003). This command sets the Program
Counter (PC) to address 0x2000 and loads the data
latches with one word of data.
After receiving a Load Configuration command, the
Configuration Word is accessed by performing an
Increment Address command 7 or 8 times to point the
PC to Configuration Word 0x2007 or 0x2008. It can
then be programmed with the loaded data using a
Begin Programming command either internally or
externally timed.
FIGURE 3-4:
3.2.6.2
After receiving this command, the chip will load in a
14-bit “data word” when 16 cycles are applied, as
described previously. A timing diagram for the Load
Data for Program Memory command is shown in
Figure 3-5.
FIGURE 3-5:
DS41287D-page 14
ICSPCLK
ICSPDAT
ICSPCLK
ICSPDAT
Load Configuration
Load Data for Program Memory
1
1
0
0
LOAD CONFIGURATION COMMAND
LOAD DATA FOR PROGRAM MEMORY COMMAND
2
2
0
0
1
T
SET
T
3
3
0
0
HLD
1
1
4
4
0
0
5
x
5
x
T
T
DLY
DLY
6
6
x
x
T
T
1
DLY
1
DLY
2
2
After the 6-bit command is input, ICSPCLK pin is
cycled an additional 16 times for the Start bit, 14 bits of
data and a Stop bit (see Figure 3-4).
After the configuration memory is entered, the only way
to get back to the program memory is to exit the
Program/Verify mode by taking MCLR low (V
1
strt_bit
1
strt_bit
2
2
LSb
LSb
T
3
T
3
SET
SET
T
T
HLD
HLD
1
1
1
1
4
4
 2009 Microchip Technology Inc.
5
5
15
15
MSb
MSb
16
16
IL
stp_bit
stp_bit
).