ATTINY861V-10PU Atmel, ATTINY861V-10PU Datasheet - Page 188

• Manufacturer Part Number: ATTINY861V-10PU
• Description: IC MCU AVR 8K FLASH 10MHZ 20-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY861V-10PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: 2-Wire/SPI/USI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Package: 20PDIP
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 10 MHz
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 19-1.
Notes:
19.3
188
Symbol
I
CC
1. Typical values at +25°C.
2. “Min” means the lowest value where the pin is guaranteed to be read as high.
3. “Max” means the highest value where the pin is guaranteed to be read as low.
4. Although each I/O port can sink more than the test conditions (10 mA at V
5. Although each I/O port can source more than the test conditions (10 mA at V
6. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a consequence,
7. Values are with external clock using methods described in
8. BOD Disabled.
Speed
ATtiny261/461/861
conditions (non-transient), the sum of all I
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition.
conditions (non-transient), the sum of all I
may exceed the related specification. Pins are not guaranteed to source current greater than the listed test condition.
has a weak drive strength as compared to regular I/O pins. See
(starting on
is enabled (PRR = 0xFF) and there is no I/O drive.
Parameter
Power Supply Current
Power-down mode
DC Characteristics. T
page
The maximum operating frequency of the device depends on V
Figure
and between 2.7V < V
Figure 19-1. Maximum Frequency vs. V
209).
(8)
10 MHz
(7)
4 MHz
19-2, the maximum frequency vs. V
A
= -40°C to +85°C, V
Condition
Active 1MHz, V
Active 4MHz, V
Active 8MHz, V
Idle 1MHz, V
Idle 4MHz, V
Idle 8MHz, V
WDT enabled, V
WDT disabled, V
1.8V
OL
OH
CC
CC
CC
CC
(for all ports) should not exceed 60 mA. If I
(for all ports) should not exceed 60 mA. If I
< 4.5V.
CC
CC
CC
= 2V
= 3V
= 5V
CC
CC
= 2V
= 3V
= 5V
= 3V
= 3V
CC
= 1.8V to 5.5V (unless otherwise noted).
“Minimizing Power Consumption” on page
CC
Figure
Safe Operating Area
Min
CC
(ATtiny261V/461V/861V)
relationship is linear between 1.8V < V
2.7V
20-23,
CC
CC
= 5V, 5 mA at V
Figure
= 5V, 5 mA at V
Typ
0.15
0.4
0.1
0.4
1.5
2
6
4
(1)
20-24,
OL
OH
CC
exceeds the test conditions, V
. As shown in
exceeds the test condition, V
Figure
CC
CC
= 3V) under steady state
Max
0.6
0.3
10
= 3V) under steady state
20-25, and
3
9
1
3
2
37. Power Reduction
Figure 19-1
5.5V
2588E–AVR–08/10
Figure 20-26
CC
Units
mA
mA
mA
mA
mA
mA
µA
µA
< 2.7V
OH
and
OL