PIC16LF1947-I/PT Microchip Technology, PIC16LF1947-I/PT Datasheet - Page 372

• Manufacturer Part Number: PIC16LF1947-I/PT
• Description: IC MCU 8BIT FLASH 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF1947-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 28KB (16K x 14)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: EUSART/I2C/SPI
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 17-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 17
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC16F/LF1946/47
28.2
The Low-Voltage Programming Entry mode allows the
PIC16F/LF1946/47 devices to be programmed using
V
Configuration Word 2 is set to ‘1’, the low-voltage ICSP
programming entry is enabled. To disable the
Low-Voltage ICSP mode, the LVP bit must be
programmed to ‘0’.
Entry into the Low-Voltage Programming Entry mode
requires the following steps:
1.
2.
Once the key sequence is complete, MCLR must be
held at V
maintained.
If low-voltage programming is enabled (LVP = 1), the
MCLR Reset function is automatically enabled and
cannot be disabled. See
information.
The LVP bit can only be reprogrammed to ‘0’ by using
the High-Voltage Programming mode.
FIGURE 28-3:
DS41414B-page 372
DD
Note:
MCLR is brought to V
A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
only, without high voltage. When the LVP bit of
IL
Low-Voltage Programming Entry
Mode
for as long as Program/Verify mode is to be
The ICD 2 produces a V
than the maximum V
PIC16F/LF1946/47.
*
PICkit™ STYLE CONNECTOR INTERFACE
Section 6.3 “MCLR”
The 6-pin header (0.100" spacing) accepts 0.025" square pins.
IL
.
PP
specification of the
PP
voltage greater
for more
Preliminary
Pin 1 Indicator
1
2
3
4
5
6
28.3
Connection to a target device is typically done
through an ICSP™ header. A commonly found
connector on development tools is the RJ-11 in the
6P6C (6 pin, 6 connector) configuration. See
Figure
FIGURE 28-2:
Another connector often found in use with the PICkit™
programmers is a standard 6-pin header with 0.1 inch
spacing. Refer to
V
28-2.
PP
V
Common Programming Interfaces
DD
/MCLR
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
Pin Description*
1 = V
2 = V
3 = V
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
PP
DD
SS
/MCLR
1
Target
(ground)
PP
DD
SS
Figure
2
3
/MCLR
4
(ground)
Target
5
V
6
SS
ICSPDAT
ICD RJ-11 STYLE
CONNECTOR INTERFACE
 2010 Microchip Technology Inc.
28-3.
ICSPCLK
NC
Target
PC Board
Bottom Side