ATMEGA164P-20MUR Atmel, ATMEGA164P-20MUR Datasheet
![MCU AVR 16KB FLASH 20MHZ 44-VQFN](/photos/12/13/121316/313-44-qfn_sml.jpg)
ATMEGA164P-20MUR
Specifications of ATMEGA164P-20MUR
Related parts for ATMEGA164P-20MUR
ATMEGA164P-20MUR Summary of contents
Page 1
... ATmega164P/324P/644PV – 2.7V - 5.5V for ATmega164P/324P/644P • Speed Grades – ATmega164P/324P/644PV MHz @ 1.8V - 5.5V MHz @ 2.7V - 5.5V – ATmega164P/324P/644P MHz @ 2.7V - 5.5V MHz @ 4.5V - 5.5V • Power Consumption at 1 MHz, 1.8V, 25°C for ATmega164P/324P/644PV – Active: 0.4 mA – ...
Page 2
... Pin Configurations 1.1 Pinout - PDIP/TQFP/VQFN/QFN/MLF Figure 1-1. Note: ATmega164P/324P/644P 2 Pinout ATmega164P/324P/644P (PCINT8/XCK0/T0) PB0 (PCINT9/CLKO/T1) PB1 (PCINT10/INT2/AIN0) PB2 (PCINT11/OC0A/AIN1) PB3 (PCINT12/OC0B/SS) PB4 (PCINT13/MOSI) PB5 (PCINT14/MISO) PB6 (PCINT15/SCK) PB7 RESET VCC GND XTAL2 XTAL1 (PCINT24/RXD0) PD0 (PCINT25/TXD0) PD1 (PCINT26/RXD1/INT0) PD2 (PCINT27/TXD1/INT1) PD3 (PCINT28/XCK1/OC1B) PD4 ...
Page 3
... Pinout - DRQFN Figure 1- Table 1- 8011OS–AVR–07/10 DRQFN - Pinout ATmega164P Top view B1 B15 B2 B14 B3 B13 B4 B12 B5 B11 DRQFN - Pinout ATmega164P/324P PB5 A7 PD3 PB6 B6 PD4 PB7 A8 PD5 RESET B7 PD6 VCC A9 PD7 GND B8 VCC XTAL2 A10 GND XTAL1 B9 PC0 PD0 A11 PC1 ...
Page 4
... Overview The ATmega164P/324P/644P is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega164P/324P/644P achieves throughputs approaching 1 MIPS per MHz allowing the sys- tem designer to optimize power consumption versus processing speed. 2.1 Block Diagram Figure 2-1 ...
Page 5
... Atmel ATmega164P/324P/644P is a powerful microcontroller that provides a highly flexible and cost effective solution to many embedded control applications. The ATmega164P/324P/644P AVR is supported with a full suite of program and system devel- opment tools including: C compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits. ...
Page 6
... As inputs, Port A pins that are externally pulled low will source current if the pull-up resistors are activated. The Port A pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port A also serves the functions of various special features of the ATmega164P/324P/644P as listed on 2.3.4 Port B (PB7:PB0) Port 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit) ...
Page 7
... through a low-pass filter. CC 2.3.11 AREF This is the analog reference pin for the Analog-to-digital Converter. 8011OS–AVR–07/10 ATmega164P/324P/644P 332. Shorter pulses are not guaranteed to generate a reset. , even if the ADC is not used. If the ADC is used, it should be connected CC ”System and Reset 7 ...
Page 8
... I/O. Typically "LDS" and "STS" combined with "SBRS", "SBRC", "SBR", and "CBR". 3.3 Data Retention Reliability Qualification results show that the projected data retention failure rate is much less than 1 PPM over 20 years at 85°C or 100 years at 25°C. ATmega164P/324P/644P 8 8011OS–AVR–07/10 ...
Page 9
... USART1 I/O Data Register - - - USART1 Baud Rate Register Low Byte - - - UMSEL10 - - TXCIE1 UDRIE1 RXEN1 TXEN1 TXC1 UDRE1 FE1 DOR1 - - - USART0 I/O Data Register - - - USART0 Baud Rate Register Low Byte - - - UMSEL00 - - TXCIE0 UDRIE0 RXEN0 TXEN0 ATmega164P/324P/644P Bit 2 Bit 1 Bit ...
Page 10
... OCR1AH (0x88) OCR1AL (0x87) ICR1H (0x86) ICR1L (0x85) TCNT1H (0x84) TCNT1L (0x83) Reserved - (0x82) TCCR1C FOC1A (0x81) TCCR1B ICNC1 (0x80) TCCR1A COM1A1 (0x7F) DIDR1 - ATmega164P/324P/644P 10 Bit 6 Bit 5 Bit 4 Bit 3 TXC0 UDRE0 FE0 DOR0 - - - - - - - - TWAM5 TWAM4 TWAM3 TWAM2 TWEA TWSTA TWSTO TWWC ...
Page 11
... Timer/Counter0 Output Compare Register A Timer/Counter0 (8 Bit) FOC0B - - WGM02 COM0A0 COM0B1 COM0B0 - - - - - - EEPROM Address Register Low Byte EEPROM Data Register - EEPM1 EEPM0 EERIE General Purpose I/O Register ATmega164P/324P/644P Bit 2 Bit 1 Bit 0 ADC2D ADC1D ADC0D - - - - MUX2 MUX1 MUX0 - ADTS2 ADTS1 ADTS0 ADPS2 ADPS1 ADPS0 - - - - ...
Page 12
... When using the I/O specific commands IN and OUT, the I/O addresses $00 - $3F must be used. When addressing I/O regis- ters as data space using LD and ST instructions, $20 must be added to these addresses. The ATmega164P/324P/644P is a complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the IN and OUT instructions ...
Page 13
... Branch if Half Carry Flag Cleared BRTS k Branch if T Flag Set BRTC k Branch if T Flag Cleared BRVS k Branch if Overflow Flag is Set 8011OS–AVR–07/10 ATmega164P/324P/644P Description Rd ← ← Rdh:Rdl ← Rdh:Rdl + K Rd ← ← ← ← Rdh:Rdl ← Rdh:Rdl - K Rd ← Rd • ← ...
Page 14
... Load Program Memory and Post-Inc ELPM Extended Load Program Memory ELPM Rd, Z Extended Load Program Memory ELPM Rd, Z+ Extended Load Program Memory ATmega164P/324P/644P 14 Description then PC ← then PC ← then PC ← I/O(P,b) ← 1 I/O(P,b) ← 0 Rd(n+1) ← Rd(n), Rd(0) ← 0 Rd(n) ← Rd(n+1), Rd(7) ← 0 Rd(0)← ...
Page 15
... MCU CONTROL INSTRUCTIONS NOP No Operation SLEEP Sleep WDR Watchdog Reset BREAK Break 8011OS–AVR–07/10 ATmega164P/324P/644P Description (Z) ← R1:R0 Rd ← ← Rr STACK ← ← STACK (see specific descr. for Sleep function) (see specific descr. for WDR/timer) For On-chip Debug Only Operation ...
Page 16
... Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN) ATmega164P/324P/644P 16 Ordering Code Package (2) ATmega164PV-10AU 44A (2) ATmega164PV-10PU 40P6 (2) ATmega164PV-10MU 44M1 (2) ATmega164P-20AU 44A (2) ATmega164P-20PU 40P6 (2) ATmega164P-20MU 44M1 329. Package Type (1) Operational Range Industrial o o (-40 ...
Page 17
... Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 40P6 40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP) 44M1 44-pad, 7 × 7 × 1.0 mm Body, lead pitch 0.50 mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN) 8011OS–AVR–07/10 ATmega164P/324P/644P Ordering Code Package (2) ATmega324PV-10AU 44A ...
Page 18
... Thin (1.0 mm) Plastic Gull Wing Quad Flat Package (TQFP) 40P6 40-pin, 0.600” Wide, Plastic Dual Inline Package (PDIP) 44M1 44-pad, 7 × 7 × 1.0 mm body, lead pitch 0.50 mm, Thermally Enhanced Plastic Very Thin Quad Flat No-Lead (VQFN) ATmega164P/324P/644P 18 Ordering Code Package (2) ...
Page 19
... Orchard Parkway San Jose, CA 95131 R 8011OS–AVR–07/10 B PIN 1 IDENTIFIER TITLE 44A, 44-lead Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) ATmega164P/324P/644P A2 A COMMON DIMENSIONS (Unit of Measure = mm) MIN SYMBOL NOM A – – A1 0.05 – ...
Page 20
... A SEATING PLANE Notes: 1. This package conforms to JEDEC reference MS-011, Variation AC. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R ATmega164P/324P/644P 20 D PIN 0º ~ 15º REF eB TITLE 40P6, 40-lead (0.600"/15.24 mm Wide) Plastic Dual ...
Page 21
... E TOP VIEW eT/2 A24 B20 0.40 R0. TITLE 44MC, 44QFN (2-Row Staggered 1.00 mm Body, 2.60 x 2.60 mm Exposed Pad, Quad Flat No Lead Package ATmega164P/324P/644P C SIDE VIEW COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 0.80 0.90 1.00 A1 0.00 0.02 0.05 b 0.18 ...
Page 22
... Errata 8.1 ATmega164P 8.1.1 Rev known Errata. 8.2 ATmega324P 8.2.1 Rev known Errata. 8.3 ATmega644P 8.3.1 Rev. A Not sampled. 8.3.2 Rev known Errata. ATmega164P/324P/644P 22 8011OS–AVR–07/10 ...
Page 23
... Updated the table note1 of the Table 25-6 on page Updated ”Typical Characteristics” on page Updated ”Typical Characteristics” on page 339 ATmega164P/324P/644P Table 25-10, “2-wire Serial Bus Require- 2. 50. 420. Removed 44MC and 49C2 packages. 423. in one section ”About” on page 9 ...
Page 24
... Updated Minimum Reference Voltage in Characteristics” on page 336. Updated bit bit field typos in ”Register Summary” on page Added 49-ball VFBGA pinout for ATmega164P/324P in Added 49-ball VFBGA (49C2) to ”Packaging Information” on page and ”Ordering Informa- 326. ”System and Reset Characteristics” rev H update. ” ...
Page 25
... Rev. 8011F- 04/07 1. 9.11 Rev. 8011E - 04/ 8011OS–AVR–07/10 Added 44-pad DRQFN pinout for ATmega164P in Added 49-ball VFBGA pinout for ATmega164P/324P in Added note to ”Address Match Unit” on page Updated ATmega164P ”Ordering Information” on page Added 44-lead QFN (44MC) to ”Packaging Information” on page Added 49-ball VFBGA (49C2) to ” ...
Page 26
... Size Configuration Updated V limits in ”DC Characteristics” on page OL Updated note 3 and 4 in ”DC Characteristics” on page Added note to ”ATmega164P DC Characteristics” on page Added note to ”ATmega324P DC Characteristics” on page Updated Figure 28-13 on page 346 Updated ”DC Characteristics” on page Updated ”DC Characteristics” on page 2 ...
Page 27
... Rev. 8011A - 08/06 1. 8011OS–AVR–07/10 Initial revision. ATmega164P/324P/644P 27 ...
Page 28
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...