AT89S8253-24JU Atmel, AT89S8253-24JU Datasheet - Page 36
![IC MCU 12K FLASH 24MHZ 44-PLCC](/photos/6/70/67043/453-44-plcc_sml.jpg)
AT89S8253-24JU
Manufacturer Part Number
AT89S8253-24JU
Description
IC MCU 12K FLASH 24MHZ 44-PLCC
Manufacturer
Atmel
Series
89Sr
Datasheet
1.AT89S8253-24PU.pdf
(60 pages)
Specifications of AT89S8253-24JU
Core Processor
8051
Core Size
8-Bit
Speed
24MHz
Connectivity
SPI, UART/USART
Peripherals
POR, WDT
Number Of I /o
32
Program Memory Size
12KB (12K x 8)
Program Memory Type
FLASH
Eeprom Size
2K x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-PLCC
Processor Series
AT89x
Core
8051
Data Bus Width
8 bit
Data Ram Size
256 B
Interface Type
SPI/UART
Maximum Clock Frequency
24 MHz
Number Of Programmable I/os
32
Number Of Timers
3
Operating Supply Voltage
2.7 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
PK51, CA51, A51, ULINK2
Development Tools By Supplier
AT89ISP
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Data Converters
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT89S8253-24JU
Manufacturer:
LITTLEFUSE
Quantity:
4 500
Company:
Part Number:
AT89S8253-24JU
Manufacturer:
ATMEL
Quantity:
6
Company:
Part Number:
AT89S8253-24JU
Manufacturer:
ATMEL
Quantity:
5 530
Company:
Part Number:
AT89S8253-24JU
Manufacturer:
ATM
Quantity:
3 290
Company:
Part Number:
AT89S8253-24JU
Manufacturer:
ATMEL
Quantity:
44 616
Part Number:
AT89S8253-24JU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
18. Power-down Mode
19. Program Memory Lock Bits
36
AT89S8253
Table 17-1.
In the power-down mode, the oscillator is stopped and the instruction that invokes power-down
is the last instruction executed. The on-chip RAM and Special Function Registers retain their
values until the power-down mode is terminated. Exit from power-down can be initiated either by
a hardware reset or by an enabled external interrupt. Reset redefines the SFRs but does not
change the on-chip RAM. The reset should not be activated before V
operating level and must be held active long enough to allow the oscillator to restart and
stabilize.
To exit power-down via an interrupt, external interrupt pin P3.2 or P3.3 must be kept low for at
least the specified required crystal oscillator start up time. Afterwards, the interrupt service rou-
tine starts at the rising edge of the external interrupt pin if the SFR bit AUXR.1 is set. If AUXR.1
is reset (cleared), execution starts after a self-timed interval of 2 ms (nominal) from the falling
edge of the external interrupt pin. The user should not attempt to enter (or re-enter) the power-
down mode for a minimum of 4 µs until after one of the following conditions has occurred: Start
of code execution (after any type of reset), or Exit from power-down mode.
The AT89S8253 has three lock bits that can be left unprogrammed (U) or can be programmed
(P) to obtain the additional features listed in
logic level at the EA pin is sampled and latched during reset. If the device is powered up without
a reset, the latch initializes to a random value and holds that value until reset is activated. The
latched value of EA must agree with the current logic level at that pin in order for the device to
function properly. Once programmed, the lock bits can only be unprogrammed with the Chip
Erase operation in either the parallel or serial modes.
Table 19-1.
Note:
Mode
Idle
Idle
Power-down
Power-down
1
2
3
4
Program Lock Bits
1. U = Unprogrammed; P = Programmed
LB1
U
P
P
P
Status of External Pins During Idle and Power-down Modes
Lock Bit Protection Modes
Program Memory
Internal
External
Internal
External
LB2
U
U
P
P
LB3
U
U
U
P
Protection Type
No internal memory lock feature.
MOVC instructions executed from external program memory are
disabled from fetching code bytes from internal memory. EA is sampled
and latched on reset and further programming of the Flash memory
(parallel or serial mode) is disabled.
Same as Mode 2, but parallel or serial verify are also disabled.
Same as Mode 3, but external execution is also disabled.
ALE
1
1
0
0
(1)
Table
PSEN
1
1
0
0
19-1. When lock bit 1 is programmed, the
PORT0
Float
Float
Data
Data
PORT1
Data
Data
Data
Data
CC
is restored to its normal
Address
PORT2
Data
Data
Data
3286P–MICRO–3/10
PORT3
Data
Data
Data
Data