PIC18F97J60T-I/PT Microchip Technology, PIC18F97J60T-I/PT Datasheet - Page 188

• Manufacturer Part Number: PIC18F97J60T-I/PT
• Description: IC PIC MCU FLASH 64KX16 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F97J60T-I/PT

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 41.667MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Type: FLASH
• Ram Size: 3808 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 70
• Ram Memory Size: 3808Byte
• Cpu Speed: 41.667MHz
• No. Of Timers: 5
• No. Of: RoHS Compliant
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3808 B
• Interface Type: Display Driver, Ethernet, EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 41.667 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 5
• Operating Supply Voltage: 2.35 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183033
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162064 - HEADER INTFC MPLABICD2 64/80/100DM163024 - BOARD DEMO PICDEM.NET 2AC164323 - MODULE SKT FOR 100TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

PIC18F97J60 FAMILY
16.3
In Compare mode, the 16-bit CCPRx register value is
constantly compared against either the TMR1 or TMR3
register pair value. When a match occurs, the CCPx
pin:
• can be driven high
• can be driven low
• can be toggled (high-to-low or low-to-high)
• remains unchanged (that is, reflects the state of
The action on the pin is based on the value of the mode
select bits (CCPxM3:CCPxM0). At the same time, the
interrupt flag bit, CCPxIF, is set.
16.3.1
The user must configure the CCPx pin as an output by
clearing the appropriate TRIS bit.
FIGURE 16-3:
DS39762E-page 188
the I/O latch)
Compare Mode
CCPx PIN CONFIGURATION
0
1
CCPR5H
COMPARE MODE OPERATION BLOCK DIAGRAM
CCPR4H
TMR1H
TMR3H
T3CCP1
Comparator
Comparator
CCPR5L
CCPR4L
TMR1L
TMR3L
Compare
Compare
Match
Match
0
1
Set CCP4IF
T3CCP2
Set CCP5IF
16.3.2
Timer1 and/or Timer3 must be running in Timer mode
or Synchronized Counter mode if the CCPx module is
using the compare feature. In Asynchronous Counter
mode, the compare operation may not work.
16.3.3
When the Generate Software Interrupt mode is chosen
(CCPxM3:CCPxM0 = 1010), the corresponding CCPx
pin is not affected. Only a CCPx interrupt is generated,
if enabled and the CCPxIE bit is set.
CCP4CON<3:0>
Note:
CCP5CON<3:0>
Output
Output
Logic
4
Logic
4
Clearing the CCP5CON register will force
the RG4 compare output latch (depend-
ing on device configuration) to the default
low level. This is not the PORTB or
PORTC I/O data latch.
TIMER1/TIMER3 MODE SELECTION
SOFTWARE INTERRUPT MODE
S
R
S
R
Q
Q
© 2009 Microchip Technology Inc.
Output Enable
Output Enable
TRIS
TRIS
CCP4 pin
CCP5 pin