PIC16LC926T-I/PT Microchip Technology, PIC16LC926T-I/PT Datasheet - Page 72
![IC MCU CMOS 20MHZ 8K W/LCD64TQFP](/photos/6/81/68123/c04-066_pf_sml.jpg)
PIC16LC926T-I/PT
Manufacturer Part Number
PIC16LC926T-I/PT
Description
IC MCU CMOS 20MHZ 8K W/LCD64TQFP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Specifications of PIC16LC926T-I/PT
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Connectivity
I²C, SPI
Peripherals
Brown-out Detect/Reset, LCD, POR, PWM, WDT
Number Of I /o
25
Program Memory Size
14KB (8K x 14)
Program Memory Type
OTP
Ram Size
336 x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TFQFP
Processor Series
PIC16LC
Core
PIC
Data Bus Width
8 bit
Data Ram Size
336 B
Interface Type
I2C, SPI
Maximum Clock Frequency
20 MHz
Number Of Programmable I/os
25
Number Of Timers
1 x 16 bit
Operating Supply Voltage
2.5 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
ICE2000
Minimum Operating Temperature
- 40 C
On-chip Adc
5 bit
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16LC926T-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC16C925/926
9.3.1
In Slave mode, the SCL and SDA pins must be config-
ured as inputs (TRISC<4:3> set). The SSP module will
override the input state with the output data when
required (slave-transmitter).
When an address is matched or the data transfer after
an address match is received, the hardware automati-
cally will generate the Acknowledge (ACK) pulse, and
then load the SSPBUF register with the received value
currently in the SSPSR register.
There are certain conditions that will cause the SSP
module not to give this ACK pulse. These are if either
(or both):
a)
b)
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set.
Table 9-3 shows what happens when a data transfer
byte is received, given the status of bits BF and
SSPOV. The shaded cells show the condition where
user software did not properly clear the overflow condi-
tion. Flag bit BF is cleared by reading the SSPBUF reg-
ister while bit SSPOV is cleared through software.
The SCL clock input must have a minimum high and
low time for proper operation. The high and low times
of the I
the SSP module is shown in timing parameter #100
and parameter #101.
9.3.1.1
Once the SSP module has been enabled, it waits for a
START condition to occur. Following the START condi-
tion, the 8-bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
TABLE 9-3:
DS39544A-page 70
Transfer is Received
Status Bits as Data
The buffer full bit BF (SSPSTAT<0>) was set
before the transfer was received.
The overflow bit SSPOV (SSPCON<6>) was set
before the transfer was received.
BF
0
1
1
0
2
C specification as well as the requirement of
SLAVE MODE
Addressing
SSPOV
DATA TRANSFER RECEIVED BYTE ACTIONS
0
0
1
1
SSPSR
Yes
No
No
No
SSPBUF
Preliminary
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match, and the BF
and SSPOV bits are clear, the following events occur:
a)
b)
c)
d)
In 10-bit Address mode, two address bytes need to be
received by the slave (Figure 9-8). The five Most Sig-
nificant bits (MSbs) of the first address byte specify if
this is a 10-bit address. Bit R/W (SSPSTAT<2>) must
specify a write so the slave device will receive the sec-
ond address byte. For a 10-bit address the first byte
would equal ‘1111 0 A9 A8 0’, where A9 and A8 are
the two MSbs of the address. The sequence of events
for a 10-bit address is as follows, with steps 7- 9 for
slave-transmitter:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Generate ACK
The SSPSR register value is loaded into the
SSPBUF register.
The buffer full bit, BF is set.
An ACK pulse is generated.
SSP interrupt flag bit, SSPIF (PIR1<3>) is set
(interrupt is generated if enabled) - on the falling
edge of the ninth SCL pulse.
Receive first (high) byte of Address (bits SSPIF,
BF, and bit UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of Address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive second (low) byte of Address (bits
SSPIF, BF, and UA are set).
Update the SSPADD register with the first (high)
byte of Address, if match releases SCL line, this
will clear bit UA.
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive Repeated START condition.
Receive first (high) byte of Address (bits SSPIF
and BF are set).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Pulse
Yes
No
No
No
(SSP Interrupt occurs
2001 Microchip Technology Inc.
Set bit SSPIF
if enabled)
Yes
Yes
Yes
Yes