PIC16F876-10E/SP Microchip Technology, PIC16F876-10E/SP Datasheet - Page 134
![IC MCU FLASH 8KX14 EE 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC16F876-10E/SP
Manufacturer Part Number
PIC16F876-10E/SP
Description
IC MCU FLASH 8KX14 EE 28DIP
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F688T-ISL.pdf
(688 pages)
3.PIC16C770-ISO.pdf
(8 pages)
4.PIC16F873-04SO.pdf
(218 pages)
5.PIC16F873-04SO.pdf
(5 pages)
6.PIC16F873-04SO.pdf
(5 pages)
Specifications of PIC16F876-10E/SP
Core Processor
PIC
Core Size
8-Bit
Speed
10MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Size
14KB (8K x 14)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 5x10b
Oscillator Type
External
Operating Temperature
-40°C ~ 125°C
Package / Case
28-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
PIC16F87610E/SP
- PIC16F616T-ISL PDF datasheet
- PIC16F688T-ISL PDF datasheet #2
- PIC16C770-ISO PDF datasheet #3
- PIC16F873-04SO PDF datasheet #4
- PIC16F873-04SO PDF datasheet #5
- PIC16F873-04SO PDF datasheet #6
- Current page: 134 of 218
- Download datasheet (4Mb)
PIC16F87X
12.13 Power-down Mode (SLEEP)
Power-down mode is entered by executing a SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared but
keeps running, the PD bit (STATUS<3>) is cleared, the
TO (STATUS<4>) bit is set, and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, low, or hi-impedance).
For lowest current consumption in this mode, place all
I/O pins at either V
cuitry is drawing current from the I/O pin, power-down
the A/D and disable external clocks. Pull all I/O pins
that are hi-impedance inputs, high or low externally, to
avoid switching currents caused by floating inputs. The
T0CKI input should also be at V
current consumption. The contribution from on-chip
pull-ups on PORTB should also be considered.
The MCLR pin must be at a logic high level (V
12.13.1
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
External MCLR Reset will cause a device RESET. All
other events are considered a continuation of program
execution and cause a “wake-up”. The TO and PD bits
in the STATUS register can be used to determine the
cause of device RESET. The PD bit, which is set on
power-up, is cleared when SLEEP is invoked. The TO
bit is cleared if a WDT time-out occurred and caused
wake-up.
The following peripheral interrupts can wake the device
from SLEEP:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Other peripherals cannot generate interrupts since dur-
ing SLEEP, no on-chip clocks are present.
DS30292C-page 132
External RESET input on MCLR pin.
Watchdog Timer Wake-up (if WDT was
enabled).
Interrupt from INT pin, RB port change or
peripheral interrupt.
PSP read or write (PIC16F874/877 only).
TMR1 interrupt. Timer1 must be operating as an
asynchronous counter.
CCP Capture mode interrupt.
Special event trigger (Timer1 in Asynchronous
mode using an external clock).
SSP (START/STOP) bit detect interrupt.
SSP transmit or receive in Slave mode
(SPI/I
USART RX or TX (Synchronous Slave mode).
A/D conversion (when A/D clock source is RC).
EEPROM write operation completion
2
C).
WAKE-UP FROM SLEEP
DD
or V
SS
, ensure no external cir-
DD
or V
SS
for lowest
IHMC
).
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction and then branches to the inter-
rupt address (0004h). In cases where the execution of
the instruction following SLEEP is not desirable, the
user should have a NOP after the SLEEP instruction.
12.13.2
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If the interrupt occurs before the execution of a
• If the interrupt occurs during or after the execu-
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
To ensure that the WDT is cleared, a CLRWDT instruc-
tion should be executed before a SLEEP instruction.
SLEEP instruction, the SLEEP instruction will com-
plete as a NOP. Therefore, the WDT and WDT
postscaler will not be cleared, the TO bit will not
be set and PD bits will not be cleared.
tion of a SLEEP instruction, the device will imme-
diately wake-up from SLEEP. The SLEEP
instruction will be completely executed before the
wake-up. Therefore, the WDT and WDT
postscaler will be cleared, the TO bit will be set
and the PD bit will be cleared.
WAKE-UP USING INTERRUPTS
2001 Microchip Technology Inc.
Related parts for PIC16F876-10E/SP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC16F876-04/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-04/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-20/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-20/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-04I/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-20I/SP](/photos/6/59/65908/150-28-dip_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-20I/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-04E/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-04I/SO](/photos/6/59/65909/150-28-soic_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 8KX14 EE 28SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-04E/SP](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,DIP,28PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC16F876-10E/SO](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SOP,28PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: