AT91SAM7X128B-CU-999 Atmel, AT91SAM7X128B-CU-999 Datasheet - Page 28

• Manufacturer Part Number: AT91SAM7X128B-CU-999
• Description: IC MCU ARM 128KB FLASH 100TFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7X128B-CU-999

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: CAN, Ethernet, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: CAN, I2S, JTAG, UASRT
• Maximum Clock Frequency: 55 MHz
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7X-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7X-EK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

9.3
9.4
28
Power Management Controller
Advanced Interrupt Controller
AT91SAM7X512/256/128 Preliminary
The Power Management Controller uses the Clock Generator outputs to provide:
The Master Clock (MCK) is programmable from a few hundred Hz to the maximum operating fre-
quency of the device.
The Processor Clock (PCK) switches off when entering processor idle mode, thus allowing
reduced power consumption while waiting for an interrupt.
Figure 9-3.
• the Processor Clock PCK
• the Master Clock MCK
• the USB Clock UDPCK
• all the peripheral clocks, independently controllable
• four programmable clock outputs
• Controls the interrupt lines (nIRQ and nFIQ) of an ARM Processor
• Individually maskable and vectored interrupt sources
• 8-level Priority Controller
– Source 0 is reserved for the Fast Interrupt Input (FIQ)
– Source 1 is reserved for system peripherals (RTT, PIT, EFC, PMC, DBGU, etc.)
– Other sources control the peripheral interrupts or external interrupts
– Programmable edge-triggered or level-sensitive internal sources
– Programmable positive/negative edge-triggered or high/low level-sensitive external
– Drives the normal interrupt nIRQ of the processor
– Handles priority of the interrupt sources
sources
Power Management Controller Block Diagram
MAINCK
PLLCK
MAINCK
SLCK
PLLCK
SLCK
PLLCK
Master Clock Controller
Programmable Clock Controller
/1,/2,/4,...,/64
Prescaler
USB Clock Controller
/1,/2,/4,...,/64
ON/OFF
Divider
/1,/2,/4
Prescaler
Processor
Controller
Idle Mode
Clock Controller
Clock
Peripherals
ON/OFF
int
UDPCK
PCK
MCK
periph_clk[2..18]
pck[0..3]
6120FS–ATARM–17-Feb-09