ATXMEGA256A3B-MH Atmel, ATXMEGA256A3B-MH Datasheet - Page 95
![MCU AVR 256KB FLASH A3B 64-QFN](/photos/12/13/121326/313-64-qfn_sml.jpg)
ATXMEGA256A3B-MH
Manufacturer Part Number
ATXMEGA256A3B-MH
Description
MCU AVR 256KB FLASH A3B 64-QFN
Manufacturer
Atmel
Series
AVR® XMEGAr
Specifications of ATXMEGA256A3B-MH
Core Processor
AVR
Core Size
8/16-Bit
Speed
32MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
49
Program Memory Size
256KB (128K x 16)
Program Memory Type
FLASH
Eeprom Size
4K x 8
Ram Size
16K x 8
Voltage - Supply (vcc/vdd)
1.6 V ~ 3.6 V
Data Converters
A/D 16x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-MLF®, 64-QFN
Processor Series
ATXMEGA256x
Core
AVR8
Data Bus Width
8 bit, 16 bit
Data Ram Size
16 KB
Interface Type
I2C, SPI, USART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
49
Number Of Timers
7
Operating Supply Voltage
1.6 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
EWAVR, EWAVR-BL
Development Tools By Supplier
ATAVRDRAGON, ATAVRISP2, ATAVRONEKIT
Minimum Operating Temperature
- 40 C
On-chip Adc
12 bit, 8 Channel
On-chip Dac
12 bit, 2 Channel
For Use With
ATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPI
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ATXMEGA256A3B-MU
ATXMEGA256A3B-MU
ATXMEGA256A3B-MU
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATXMEGA256A3B-MH
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
36. Errata
36.1
36.1.1
8116I–AVR–09/10
ATxmega256A3B
rev. C
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
1. Bandgap voltage input for the ACs cannot be changed when used for both ACs
2. VCC voltage scaler for AC is non-linear
Bandgap voltage input for the ACs can not be changed when used for both ACs simultaneously
VCC voltage scaler for AC is non-linear
ADC has increased INL error for some operating conditions
ADC gain stage non-functional
ADC Event on compare match non-functional
Bandgap measurement with the ADC is non-functional when VCC is below 2.7V
Configuration of PGM and CWCM not as described in XMEGA A Manual
PWM is not restarted properly after a fault in cycle-by-cycle mode
BOD will be enabled at any reset
DAC is nonlinear and inaccurate when reference is above 2.4V or VCC - 0.6V
DAC has increased INL or noise for some operating conditions
DAC refresh may be blocked in S/H mode
Conversion lost on DAC channel B in event triggered mode
EEPROM page buffer always written when NVM DATA0 is written
Pending full asynchronous pin change interrupts will not wake the device
Pin configuration does not affect Analog Comparator Output
NMI Flag for Crystal Oscillator Failure automatically cleared
Crystal start-up time required after power-save even if crystal is source for RTC
TWI Transmit collision flag not cleared on repeated start
Clearing TWI Stop Interrupt Flag may lock the bus
TWI START condition at bus timeout will cause transaction to be dropped
TWI Data Interrupt Flag (DIF) erroneously read as set
WDR instruction inside closed window will not issue reset
Pending asynchronous RTC32-interrupts will not wake up device
XOSCDFD can not be cleared by writing one to bit location
Maximum operating frequency below 1.76V is 8 MHz
simultaneously
If the Bandgap voltage is selected as input for one Analog Comparator (AC) and then
selected/deselected as input for another AC, the first comparator will be affected for up to
1 µs and could potentially give a wrong comparison result.
Problem fix/Workaround
If the Bandgap is required for both ACs simultaneously, configure the input selection for both
ACs before enabling any of them.
The 6-bit VCC voltage scaler in the Analog Comparators is non-linear.
XMEGA A3B
95