ST7FLITE05Y0M6 STMicroelectronics, ST7FLITE05Y0M6 Datasheet - Page 63
![MCU 8BIT 1.5K FLASH 16-SOIC](/photos/1/39/13919/497-16-soic_series_sml.jpg)
ST7FLITE05Y0M6
Manufacturer Part Number
ST7FLITE05Y0M6
Description
MCU 8BIT 1.5K FLASH 16-SOIC
Manufacturer
STMicroelectronics
Series
ST7r
Datasheet
1.ST7FLITES2Y0B6.pdf
(124 pages)
Specifications of ST7FLITE05Y0M6
Core Processor
ST7
Core Size
8-Bit
Speed
16MHz
Connectivity
SPI
Peripherals
LVD, POR, PWM, WDT
Number Of I /o
13
Program Memory Size
1.5KB (1.5K x 8)
Program Memory Type
FLASH
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
2.4 V ~ 5.5 V
Data Converters
A/D 5x8b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC (3.9mm Width)
Processor Series
ST7FLITE0x
Core
ST7
Data Bus Width
8 bit
Data Ram Size
128 B
Interface Type
SPI
Maximum Clock Frequency
8 MHz
Number Of Programmable I/os
13
Number Of Timers
2
Operating Supply Voltage
2.4 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Development Tools By Supplier
ST7FLIT0-IND/USB, ST7FLITE-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
Minimum Operating Temperature
- 40 C
On-chip Adc
5-ch x 8-bit
For Use With
497-5858 - EVAL BOARD PLAYBACK ST7FLITE497-5080 - EVAL BOARD AC/AC CHOPPER DRIVER497-5049 - KIT STARTER RAISONANCE ST7FLITE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
497-9030-5
ST7FLITE05Y0M6
ST7FLITE05Y0M6
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ST7FLITE05Y0M6
Manufacturer:
ST
Quantity:
20 000
SERIAL PERIPHERAL INTERFACE (Cont’d)
11.3.4 Clock Phase and Clock Polarity
Four possible timing relationships may be chosen
by software, using the CPOL and CPHA bits (See
Figure
Note: The idle state of SCK must correspond to
the polarity selected in the SPICSR register (by
pulling up SCK if CPOL=1 or pulling down SCK if
CPOL=0).
The combination of the CPOL clock polarity and
CPHA (clock phase) bits selects the data capture
clock edge
Figure 41. Data Clock Timing Diagram
(from slave)
(from slave)
41).
(to slave)
(to slave)
(from master)
(from master)
SCK
(CPOL = 0)
MISO
MOSI
CAPTURE STROBE
SCK
(CPOL = 1)
SCK
(CPOL = 0)
MISO
MOSI
CAPTURE STROBE
SCK
(CPOL = 1)
SS
SS
Note: This figure should not be used as a replacement for parametric information.
Refer to the Electrical Characteristics chapter.
MSBit
MSBit
MSBit
MSBit
Bit 6
Bit 6
Bit 6
Bit 6
Bit 5
Bit 5
Bit 5
Bit 5
CPHA =0
CPHA =1
Bit 4
Bit 4
Bit 4
Bit 4
Figure
combinations of the CPHA and CPOL bits. The di-
agram may be interpreted as a master or slave
timing diagram where the SCK pin, the MISO pin,
the MOSI pin are directly connected between the
master and the slave device.
Note: If CPOL is changed at the communication
byte boundaries, the SPI must be disabled by re-
setting the SPE bit.
Bit3
Bit3
Bit3
Bit3
41, shows an SPI transfer with the four
Bit 2
Bit 2
Bit 2
Bit 2
ST7LITE0xY0, ST7LITESxY0
Bit 1
Bit 1
Bit 1
Bit 1
LSBit
LSBit
LSBit
LSBit
63/124
1