C8051F333-GMR Silicon Laboratories Inc, C8051F333-GMR Datasheet - Page 92

• Manufacturer Part Number: C8051F333-GMR
• Description: IC 8051 MCU 4K FLASH 20MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F33xr

Specifications of C8051F333-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-QFN
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: KSK-SL-TOOLSTICK, PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F330DK
• Minimum Operating Temperature: - 40 C
• For Use With: 336-1451 - ADAPTER PROGRAM TOOLSTICK F330
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

9.4.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruc-
tion that sets the bit completes execution. In Stop mode the internal oscillator, CPU, and all digital peripher-
als are stopped; the state of the external oscillator circuit is not affected. Each analog peripheral (including
the external oscillator circuit) may be shut down individually prior to entering Stop Mode. Stop mode can
only be terminated by an internal or external reset. On reset, the CIP-51 performs the normal reset
sequence and begins program execution at address 0x0000.
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode.
The Missing Clock Detector should be disabled if the CPU is to be put to in STOP mode for longer than the
MCD timeout of 100 µs.
Bits7–2: GF5–GF0: General Purpose Flags 5–0.
Bit1:
Bit0:
GF5
R/W
Bit7
These are general purpose flags for use under software control.
STOP: Stop Mode Select.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: CPU goes into Stop mode (internal oscillator stopped).
IDLE: Idle Mode Select.
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: CPU goes into Idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial
Ports, and Analog Peripherals are still active.)
GF4
R/W
Bit6
SFR Definition 9.12. PCON: Power Control
GF3
R/W
Bit5
GF2
R/W
Bit4
Rev. 1.7
GF1
R/W
Bit3
GF0
R/W
Bit2
C8051F330/1/2/3/4/5
STOP
R/W
Bit1
IDLE
R/W
Bit0
SFR Address:
00000000
Reset Value
0x87
95