MC908GR16VFAE Freescale Semiconductor, MC908GR16VFAE Datasheet - Page 235

• Manufacturer Part Number: MC908GR16VFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16VFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

ELSxB and ELSxA — Edge/Level Select Bits
TOVx — Toggle On Overflow Bit
CHxMAX — Channel x Maximum Duty Cycle Bit
Freescale Semiconductor
When channel x is an input capture channel, these read/write bits control the active edge-sensing logic
on channel x.
When channel x is an output compare channel, ELSxB and ELSxA control the channel x output
behavior when an output compare occurs.
When ELSxB and ELSxA are both clear, channel x is not connected to port D, and pin PTDx/TCHx is
available as a general-purpose I/O pin.
the ELSxB and ELSxA bits.
When channel x is an output compare channel, this read/write bit controls the behavior of the channel
x output when the TIM counter overflows. When channel x is an input capture channel, TOVx has no
effect. Reset clears the TOVx bit.
When the TOVx bit is at 1, setting the CHxMAX bit forces the duty cycle of buffered and unbuffered
PWM signals to 100%. As
or cleared. The output stays at the 100% duty cycle level until the cycle after CHxMAX is cleared.
1 = Channel x pin toggles on TIM counter overflow.
0 = Channel x pin does not toggle on TIM counter overflow.
MSxB:MSxA ELSxB:ELSxA
Before enabling a TIM channel register for input capture operation, make
sure that the PTD/TCHx pin is stable for at least two bus clocks.
When TOVx is set, a TIM counter overflow takes precedence over a
channel x output compare if both occur at the same time.
X0
X1
1X
1X
1X
00
00
00
01
01
01
Table 18-3. Mode, Edge, and Level Selection
Figure 18-12
00
00
01
10
11
01
10
11
01
10
11
MC68HC908GR16 Data Sheet, Rev. 5.0
Output compare
Buffered output
or buffered
Table 18-3
compare
or PWM
capture
shows, the CHxMAX bit takes effect in the cycle after it is set
Output
preset
Mode
PWM
Input
NOTE
NOTE
shows how ELSxB and ELSxA work. Reset clears
Pin under port control; initial output level high
Pin under port control; initial output level low
Capture on rising edge only
Capture on falling edge only
Capture on rising or falling edge
Toggle output on compare
Clear output on compare
Set output on compare
Toggle output on compare
Clear output on compare
Set output on compare
Configuration
I/O Registers
235