MCF52254CAF66 Freescale Semiconductor, MCF52254CAF66 Datasheet - Page 31

• Manufacturer Part Number: MCF52254CAF66
• Description: MCU 32BIT COLDFIRE V2 100LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF5225xr

Specifications of MCF52254CAF66

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: CAN, Ethernet, I²C, QSPI, UART/USART, USB OTG
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 56
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: MCF522x
• Core: ColdFire V2
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: I2C/QSPI/UART
• Maximum Clock Frequency: 66 MHz
• Number Of Programmable I/os: 56
• Number Of Timers: 10
• Operating Supply Voltage: - 0.3 V to + 4 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: TWR-MCF5225X, TWR-SENSOR-PAK, TWR-SER, TWR-ELEV, TOWER, M52259EVB, M52259DEMOKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical Characteristics
2.8
1
2
3
4
5
6
7
8
9
10
11
31
Clock Source Frequency Range of EXTAL Frequency Range
PLL reference frequency range
System frequency
Loss of reference frequency
Self clocked mode frequency
Crystal start-up time
EXTAL input high voltage
EXTAL input low voltage
PLL lock time
Duty cycle of reference
Frequency un-LOCK range
Frequency LOCK range
CLKOUT period jitter
On-chip oscillator frequency
• Crystal
• External
• External clock mode
• On-chip PLL frequency
• External reference
• External reference
• Peak-to-peak (clock edge to clock edge)
• Long term (averaged over 2 ms interval)
In external clock mode, it is possible to run the chip directly from an external clock source without enabling the PLL.
This value has been updated.
All internal registers retain data at 0 Hz.
Depending on packaging; see the orderable part number summary.
Loss of Reference Frequency is the reference frequency detected internally, which transitions the PLL into self clocked mode.
Self clocked mode frequency is the frequency at which the PLL operates when the reference frequency falls below f
default MFD/RFD settings.
This parameter is characterized before qualification rather than 100% tested.
Proper PC board layout procedures must be followed to achieve specifications.
This specification applies to the period required for the PLL to relock after changing the MFD frequency control bits in the
synthesizer control register (SYNCR).
Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f
Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise
injected into the PLL circuitry via V
for a given interval.
Based on slow system clock of 40 MHz measured at f
1
Clock Source Electrical Specifications
4,9
3
7, 8
4, 5, 10 ,11
4
Characteristic
5, 7
6
, measured at f
DDPLL
(V
Table 14. Oscillator and PLL Specifications
DD
MCF52259 ColdFire Microcontroller, Rev. 4
and V
and V
SYS
SSPLL
DDPLL
Max
and variation in crystal oscillator frequency increase the C
= 3.0 to 3.6 V, V
sys
max.
SS
Symbol
V
V
f
f
C
crystal
f
ref_pll
f
f
IHEXT
f
SCM
ILEXT
f
f
LOR
= V
t
t
f
LCK
t
oco
sys
ext
cst
lpll
UL
jitter
dc
SSPLL
= 0 V)
f
ref
–0.75
–1.5
7.84
Min
100
V
2.0
12
—
—
40
—
—
0
2
0
1
SS
/ 32
66.67 or 80
66.67 or 80
66.67 or 80
Freescale Semiconductor
25.0
1000
Max
10.0
0.75
8.16
3.0
500
0.1
0.8
1.5
.01
60
10
5
2
2
jitter
4
4
percentage
sys
% f
LOR
% f
% f
% f
MHz
MHz
MHz
MHz
MHz
Unit
.
kHz
ms
s
V
V
sys
ref
ref
ref
with