M30280F6HP#D5 Renesas Electronics America, M30280F6HP#D5 Datasheet - Page 80

• Manufacturer Part Number: M30280F6HP#D5
• Description: IC M16C MCU FLASH 48K 80-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30280F6HP#D5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 71
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 80-LQFP
• For Use With: M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M
R
R
e
E
1
. v
Table 7.4 Interrupts to Exit Wait Mode
J
6
0
NMI interrupt
Serial I/O interrupt
Multi-Master I
key input interrupt
A/D conversion
interrupt
Timer A interrupt
Timer B interrupt
Timer S interrupt
INT interrupt
Interrupt
C
interrupt
2
9
0 .
2 /
B
7.6.2.3 Pin Status During Wait Mode
7.6.2.4 Exiting Wait Mode
0
0
8
0
The I/O port pins retain their status held just prior to wait mode.
The microcomputer is moved out of wait mode by a hardware reset, NMI interrupt or peripheral func-
tion interrupt.
If the microcomputer is to be moved out of exit wait mode by a hardware reset or NMI interrupt, set the
peripheral function interrupt priority ILVL2 to ILVL0 bits to “000
ing the WAIT instruction.
The peripheral function interrupts are affected by the CM02 bit. If CM02 bit is set to “0” (peripheral
function clocks not turned off during wait mode), peripheral function interrupts can be used to exit wait
mode. If CM02 bit is set to “1” (peripheral function clocks turned off during wait mode), the peripheral
functions using the peripheral function clocks stop operating, so that only the peripheral functions
clocked by external signals can be used to exit wait mode.
Table 7.4 lists the interrupts to exit wait mode.
If the microcomputer is to be moved out of wait mode by a peripheral function interrupt, set up the
following before executing the WAIT instruction.
The CPU clock turned on when exiting wait mode by a peripheral function interrupt is the same CPU
clock that was on when the WAIT instruction was executed.
4
G
J
1. In the ILVL2 to ILVL0 bits of interrupt control register, set the interrupt priority level of the periph
2. Set the I flag to “1”.
3. Enable the peripheral function whose interrupt is to be used to exit wait mode.
7
a
o r
0 -
. n
Also, for all of the peripheral function interrupts not used to exit wait mode, set the ILVL2 to ILVL0
bits to “000
In this case, when an interrupt request is generated and the CPU clock is thereby turned on, an
interrupt routine is executed.
eral function interrupt to be used to exit wait mode.
u
2
3
p
0
2
, 1
0
C
(
M
2
0
1
0
6
7
C
2
2 /
” (interrupt disable).
Can be used
Can be used when operating
with internal or external clock
Can be used
Can be used
Can be used in all modes
Can be used in all modes
Can be used
Can be used in one-shot mode
or single sweep mode
CM02=0
, 8
page 58
M
1
6
C
f o
2 /
8
3
) B
8
5
Can be used when operating
with external clock
Can be used
Can be used
Can be used in event counter
mode or when the count
source is f
Can be used
CM02=1
(Do not use)
(Do not use)
(Do not use)
C32
2
” (interrupts disabled) before execut-
______
7. Clock Generation Circuit
______