C8051F017-GQ Silicon Laboratories Inc, C8051F017-GQ Datasheet - Page 169

• Manufacturer Part Number: C8051F017-GQ
• Description: IC 8051 MCU 32K FLASH 32LQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F01xr

Specifications of C8051F017-GQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-LQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 4x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F005DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• On-chip Dac: 2-ch x 12-bit
• No. Of I/o's: 8
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1196

169
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
DATA7
This register is used to read or write data to the Flash memory across the JTAG interface.
Bits9-2: DATA7-0: Flash Data Byte.
Bit1:
Bit0:
This register controls the Flash read timing circuit and the prescaler required to generate the correct
timing for Flash operations.
Bit7:
Bit6:
Bits5-4: UNUSED. Read = 00b, Write = don’t care.
Bits3-0: FLSCL3-0: Flash Prescaler Control Bits.
Bit9
FOSE
Bit7
FAIL: Flash Fail Bit.
0:
1:
0:
1:
0: Flash read strobe is a full clock-cycle wide.
1: Flash read strobe is 50nsec.
0: The Flash output enable and sense amplifier enable are on only when needed to read the
1: The Flash output enable and sense amplifier enable are always on. This can be used to
The FLSCL3-0 bits control the prescaler used to generate timing signals for Flash
operations. Its value should be written before any Flash operations are initiated. The value
written should be the smallest integer for which:
Where f
disallowed when FLSCL[3:0] = 1111b.
FBUSY: Flash Busy Bit.
FOSE: Flash One-Shot Enable Bit.
FRAE: Flash Read Always Bit.
DATA6
Bit8
Flash memory.
limit the variations in digital supply current due to switching the sense amplifiers, thereby
reducing digitally induced noise.
FRAE
Bit6
Previous Flash memory operation was successful.
Previous Flash memory operation failed. Usually indicates the associated memory
location was locked.
Flash interface logic is not busy.
Flash interface logic is processing a request. Reads or writes while FBUSY = 1 will
not initiate another operation
SYSCLK
FLSCL[3:0] > log
DATA5
Figure 21.5. FLASHDAT: JTAG Flash Data Register
Figure 21.6. FLASHSCL: JTAG Flash Scale Register
Bit7
is the system clock frequency. All Flash read/write/erase operations are
Bit5
-
DATA4
Bit6
2
(f
SYSCLK
DATA3
Bit4
Bit5
-
/ 50kHz)
Rev. 1.7
DATA2
FLSCL3
Bit4
Bit3
DATA1
Bit3
FLSCL2
Bit2
DATA0
Bit2
FLSCL1
Bit1
FAIL
Bit1
FLSCL0
FBUSY
Bit0
Bit0
Reset Value
Reset Value
0000000000
00000000