MCF5234CVM150J Freescale Semiconductor, MCF5234CVM150J Datasheet - Page 26

• Manufacturer Part Number: MCF5234CVM150J
• Description: IC MCU 64K 150MHZ 256MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF523xr

Specifications of MCF5234CVM150J

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, WDT
• Number Of I /o: 97
• Program Memory Type: ROMless
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 1.4 V ~ 1.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Family Name: MCF5xxx
• Device Core: ColdFire
• Device Core Size: 32b
• Frequency (max): 150MHz
• Instruction Set Architecture: RISC
• Supply Voltage 1 (typ): 3.3V
• Operating Supply Voltage (max): 1.6/3.6V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 256
• Package Type: MA-BGA
• Processor Series: MCF523x
• Core: ColdFire V2
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: NNDK-MOD5234-KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant

Electrical Characteristics
26
1
2
3
4
5
6
7
8
Input Capacitance
Load Capacitance
Core Operating Supply Current
Pad Operating Supply Current
DC Injection Current
All input-only pins
All input/output (three-state) pins
Low drive strength
High drive strength
Master Mode
Master Mode
Low Power Modes
Single Pin Limit
Total processor Limit, Includes sum of all stressed pins
Refer to Table 10 for additional PLL specifications.
Refer to the MCF5235 signals section for pins having weak internal pull-up devices.
This parameter is characterized before qualification rather than 100% tested.
pF load ratings are based on DC loading and are provided as an indication of driver strength. High speed interfaces require
transmission line analysis to determine proper drive strength and termination. See High Speed Signal Propagation:
Advanced Black Magic by Howard W. Johnson for design guidelines.
Current measured at maximum system clock frequency, all modules active, and default drive strength with matching load.
All functional non-supply pins are internally clamped to V
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
Power supply must maintain regulation within operating V
conditions. If positive injection current (V
result in external power supply going out of regulation. Insure external V
injection current. This will be the greatest risk when the processor is not consuming power. Examples are: if no system
clock is present, or if clock rate is very low which would reduce overall power consumption. Also, at power-up, system clock
is not present during the power-up sequence until the PLL has attained lock.
V
NEGCLAMP
=V
4
SS
3
– 0.3 V, V
3, 6, 7, 8
Characteristic
MCF523x Integrated Microprocessor Hardware Specification, Rev. 4
POSCLAMP
5
Table 9. DC Electrical Specifications
= V
in
> V
DD
DD
+ 0.3
) is greater than I
SS
DD
and their respective V
range during instantaneous and operating maximum current
Symbol
OI
I
C
C
I
DD
IC
DD
in
L
DD
, the injection current may flow out of V
DD
1
load will shunt current greater than maximum
(continued)
–1.0
Min
–10
—
—
—
—
—
DD
.
Typical
TBD
135
100
—
—
—
Freescale Semiconductor
Max
150
1.0
25
50
10
—
—
7
7
DD
and could
Unit
mA
mA
mA
mA
pF
pF
pF
μA