MAXQ610A-0000+ Maxim Integrated Products, MAXQ610A-0000+ Datasheet - Page 25

• Manufacturer Part Number: MAXQ610A-0000+
• Description: IC MCU 16BIT 64K IR MOD 32TQFN
• Manufacturer: Maxim Integrated Products
• Series: MAXQ™r

Specifications of MAXQ610A-0000+

• Core Processor: RISC
• Core Size: 16-Bit
• Speed: 12MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Infrared, Power-Fail, POR, WDT
• Number Of I /o: 20
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 32-TQFN Exposed Pad
• Processor Series: MAXQ610
• Core: RISC
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: SPI, USART
• Maximum Clock Frequency: 12 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 1.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Controller Family/series: MAXQ
• No. Of I/o's: 24
• Ram Memory Size: 2048Byte
• Cpu Speed: 12MHz
• No. Of Timers: 2
• Embedded Interface Type: JTAG, SPI, USART
• Rohs Compliant: Yes
• Number Of Programmable I/os: 32
• Development Tools By Supplier: MAXQ610-KIT
• Package: 32TQFN EP
• Family Name: MAXQ
• Maximum Speed: 12 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 90-M6800+B01

Table 6. Stop Mode Power-Fail Detection States with Power-Fail Monitor Disabled (continued)
The low-power, high-performance RISC architecture of
this device makes it an excellent fit for many portable or
battery-powered applications. It is ideally suited for
applications such as universal remote controls that
require the cost-effective integration of IR
transmit/receive capability.
Careful PCB layout significantly minimizes system-level
digital noise that could interact with the microcontroller
or peripheral components. The use of multilayer boards
is essential to allow the use of dedicated power planes.
The area under any digital components should be a
continuous ground plane if possible. Keep any bypass
capacitor leads short for best noise rejection and place
the capacitors as close to the leads of the devices as
possible.
CMOS design guidelines for any semiconductor require
that no pin be taken above V
Violation of this guideline can result in a hard failure
(damage to the silicon inside the device) or a soft fail-
ure (unintentional modification of memory contents).
Voltage spikes above or below the device’s absolute
maximum ratings can potentially cause a devastating
IC latchup.
Microcontrollers commonly experience negative volt-
age spikes through either their power pins or general-
purpose I/O pins. Negative voltage spikes on power
pins are especially problematic as they directly couple
to the internal power buses. Devices such as keypads
can conduct electrostatic discharges directly into the
microcontroller and seriously damage the device.
STATE
D
E
F
POWER-FAIL
(Periodically)
16-Bit Microcontroller with Infrared Module
Off
On
Off
Applications Information
______________________________________________________________________________________
Grounds and Bypassing
REGULATOR
INTERNAL
Off
Off
Off
DD
or below GND.
OSCILLATOR
CRYSTAL
Off
Off
Off
RETENTION
SRAM
Yes
Yes
System designers must protect components against
these transients that can corrupt system memory.
The ROM-only versions of the MAXQ610 family devices
operate in the same manner as their flash counterparts
with the following exceptions:
• The ROM loader is not available in the ROM version.
• Loading memory and in-application programming
• The debugger is not available in the ROM version.
Designers must have the following documents to fully
use all the features of this device. This data sheet con-
tains pin descriptions, feature overviews, and electrical
specifications. Errata sheets contain deviations from
published specifications. The user’s guides offer
detailed information about device features and opera-
tion. The following documents can be downloaded from
www.maxim-ic.com/microcontrollers.
• This MAXQ610 data sheet, which contains electrical/
• The MAXQ610 revision-specific errata sheet
• The MAXQ Family User's Guide , which contains
• The MAXQ Family User's Guide: MAXQ610
—
are not supported.
timing specifications and pin descriptions.
(www.maxim-ic.com/errata).
detailed information on core features and operation,
including programming.
Supplement , which contains detailed information on
features specific to the MAXQ610.
Differences for ROM Versions
Application enters stop mode.
V
CPU in stop mode.
V
An interrupt occurs that causes the CPU to exit
stop mode.
Power-fail monitor is turned on, detects a power-
fail, puts CPU in reset.
Power-fail monitor is turned on periodically.
V
Device held in reset. No operation allowed.
DD
POR
DD
> V
< V
Additional Documentation
< V
RST
POR
DD
.
< V
RST
COMMENTS
.
25