UPD78F1174AGF-GAT-AX Renesas Electronics America, UPD78F1174AGF-GAT-AX Datasheet - Page 929

• Manufacturer Part Number: UPD78F1174AGF-GAT-AX
• Description: MCU 16BIT 78K0R/KX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3r

Specifications of UPD78F1174AGF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, EBI/EMI, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

A/D
converter
Function
Registers used
by temperature
sensors
Procedure for
using
temperature
sensors
Operating
current in STOP
mode
Reducing
current when
A/D converter is
stopped
Input range of
ANI0 to ANI15
Conflicting
operations
Details of
Function
Shift to STOP mode after clearing the A/D converter (by clearing bit 7 (ADCS) of the
A/D converter mode register (ADM) to 0). The operating current can be reduced by
clearing bit 0 (ADCE) of the A/D converter mode register (ADM) to 0 at the same time.
When using a temperature sensor, use the result of the second or later A/D
conversion for temperature sensor 0 (ANI0 side), and the result of the third or later
A/D conversion for temperature sensor 1 (ANI1 side).
Be sure to clear bits 4 to 6 to “0”.
Make sure the period of <2> to <5> is 1
the result of the third and later conversion becomes valid on the sensor 0 side.
<2> can be done between <3> and <4>.
The period from <7> to <10> differs from the conversion time set using bits 5 to 1
(FR2 to FR0, LV1, LV0) of ADM. The period from <9> to <10> is the conversion time
set using FR2 to FR0, LV1, and LV0.
Do not change the AV
sensor detection value does not depend on the AV
problem even if the AV
be stable during a measurement cycle (from <4> to <13>).
Use the result of the second or later A/D conversion for temperature sensor 0 (ANI0
side), and the result of the third or later A/D conversion for temperature sensor 1
(ANI1 side).
To restart from the standby status, clear bit 0 (ADIF) of interrupt request flag register
1L (IF1L) to 0 and start operation.
Be sure that the voltage to be applied to AV
stated in Table 11-1.
If bit 7 (ADCS) and bit 0 (ADCE) of the A/D converter mode register (ADM) are set to
0, the current will not be increased by the A/D converter even if a voltage is applied to
AV
that supplies a voltage to AV
in Figure 11-25, AV
be reduced by satisfying the following conditions (see the main text).
Observe the rated range of the ANI0 to ANI15 input voltage. If a voltage of AV
higher and AV
an analog input channel, the converted value of that channel becomes undefined. In
addition, the converted values of the other channels may also be affected.
Conflict between A/D conversion result register (ADCR, ADCRH) write and ADCR or
ADCRH read by instruction upon the end of conversion
ADCR or ADCRH read has priority. After the read operation, the new conversion
result is written to ADCR or ADCRH.
Conflict between ADCR or ADCRH write and A/D converter mode register (ADM)
write, analog input channel specification register (ADS), or A/D port configuration
register (ADPC) write upon the end of conversion
ADM, ADS, or ADPC write has priority. ADCR or ADCRH write is not performed, nor
is the conversion end interrupt signal (INTAD) generated.
REF0
, while the A/D converter is stopped. If a current flows from the power supply
APPENDIX B LIST OF CAUTIONS
User’s Manual U18432EJ5V0UD
SS
or lower (even in the range of absolute maximum ratings) is input to
REF0
REF0
REF0
= 0 V = AV
voltage varies at every temperature measurement, it must
voltage during <4> to <13>. Although the temperature
REF0
to an external circuit of the microcontroller as shown
SS
Cautions
can be achieved and the external current can
μ
s or more. If ADCS is set to 1 within 1
REF0
normally satisfies the conditions
REF0
voltage and thus there is no
REF0
μ
or
s,
p.389
p.389
p.393
p.393
p.393
p.393
p.394
p.397
p.397
p.398
p.398
p.398
(15/35)
927
Page