AT90LS8535-4PI Atmel, AT90LS8535-4PI Datasheet - Page 43
![IC MCU 8K 4MHZ A/D LV IT 40DIP](/photos/6/70/67049/453-40-dip_sml.jpg)
AT90LS8535-4PI
Manufacturer Part Number
AT90LS8535-4PI
Description
IC MCU 8K 4MHZ A/D LV IT 40DIP
Manufacturer
Atmel
Series
AVR® 90LSr
Specifications of AT90LS8535-4PI
Core Processor
AVR
Core Size
8-Bit
Speed
4MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
8KB (4K x 16)
Program Memory Type
FLASH
Eeprom Size
512 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
2.7 V ~ 6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Timer/Counter2 Control
Register – TCCR2
1041H–11/01
Timer/Counter Control Register (TCCR2). The interrupt enable/disable settings are
found in the Timer/Counter Interrupt Mask Register (TIMSK).
This module features a high-resolution and a high-accuracy usage with the lower pres-
caling opportunities. Similarly, the high prescaling opportunities make this unit useful for
lower speed functions or exact timing functions with infrequent actions.
The Timer/Counter supports an Output Compare function using the Output Compare
Register (OCR2) as the data source to be compared to the Timer/Counter contents.The
Output Compare function includes optional clearing of the counter on compare match
and action on the Output Compare Pin, PD7(OC2), on compare match. Writing to
PORTD7 does not set the OC2 value to a predetermined value.
Timer/Counter2 can also be used as an 8-bit Pulse Width Modulator. In this mode,
Timer/Counter2 and the Output Compare Register serve as a glitch-free, stand-alone
PWM with centered pulses. Refer to page 45 for a detailed description of this function.
• Bit 7 – Res: Reserved Bit
This bit is a reserved bit in the AT90S8535 and always reads as zero.
• Bit 6 – PWM2: Pulse Width Modulator Enable
When set (one), this bit enables PWM mode for Timer/Counter2. This mode is described
on page 45.
• Bits 5, 4 – COM21, COM20: Compare Output Mode, Bits 1 and 0
The COM21 and COM20 control bits determine any output pin action following a com-
pare match in Timer/Counter2. Output pin actions affect pin PD7(OC2). This is an
alternative function to an I/O port and the corresponding direction control bit must be set
(one) to control an output pin. The control configuration is shown in Table 17.
Table 17. Compare Mode Select
Note:
• Bit 3 – CTC2: Clear Timer/Counter on Compare Match
When the CTC2 control bit is set (one), Timer/Counter2 is reset to $00 in the CPU clock
cycle after a compare match. If the control bit is cleared, Timer/Counter2 continues
counting and is unaffected by a compare match. Since the compare match is detected in
the CPU clock cycle following the match, this function will behave differently when a
prescaling higher than 1 is used for the timer. When a prescaling of 1 is used and the
compare2 register is set to C, the timer will count as follows if CTC2 is set:
... | C-2 | C-1 | C | 0 | 1 |...
Bit
$25 ($45)
Read/Write
Initial Value
COM21
0
0
1
1
In PWM mode, these bits have a different function. Refer to Table 19 for a detailed
description.
R
7
–
0
COM20
0
1
0
1
PWM2
R/W
6
0
Description
Timer/Counter disconnected from output pin OC2
Toggle the OC2 output line.
Clear the OC2 output line (to zero).
Set the OC2 output line (to one).
COM21
R/W
5
0
COM20
R/W
4
0
CTC2
R/W
3
0
CS22
R/W
2
0
AT90S/LS8535
CS21
R/W
1
0
CS20
R/W
0
0
TCCR2
43