ATTINY11L-2PI Atmel, ATTINY11L-2PI Datasheet

IC AVR MCU 1K 2MHZ LV IND 8-DIP

ATTINY11L-2PI

Manufacturer Part Number
ATTINY11L-2PI
Description
IC AVR MCU 1K 2MHZ LV IND 8-DIP
Manufacturer
Atmel
Series
AVR® ATtinyr
Datasheets

Specifications of ATTINY11L-2PI

Core Processor
AVR
Core Size
8-Bit
Speed
2MHz
Peripherals
WDT
Number Of I /o
6
Program Memory Size
1KB (512 x 16)
Program Memory Type
FLASH
Voltage - Supply (vcc/vdd)
2.7 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Ram Size
-
Data Converters
-
Connectivity
-
Other names
ATTINY11L2PI

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATTINY11L-2PI
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Features
Pin Configuration
(RESET) PB5
Utilizes the AVR
High-performance and Low-power 8-bit RISC Architecture
Nonvolatile Program and Data Memory
Peripheral Features
Special Microcontroller Features
Specification
Power Consumption at 4 MHz, 3V, 25°C
Packages
Operating Voltages
Speed Grades
(XTAL1) PB3
(XTAL2) PB4
– 90 Powerful Instructions – Most Single Clock Cycle Execution
– 32 x 8 General Purpose Working Registers
– Up to 8 MIPS Throughput at 8 MHz
– 1K Byte of Flash Program Memory
– 64 Bytes of In-System Programmable EEPROM Data Memory for ATtiny12
– Programming Lock for Flash Program and EEPROM Data Security
– Interrupt and Wake-up on Pin Change
– One 8-bit Timer/Counter with Separate Prescaler
– On-chip Analog Comparator
– Programmable Watchdog Timer with On-chip Oscillator
– Low-power Idle and Power-down Modes
– External and Internal Interrupt Sources
– In-System Programmable via SPI Port (ATtiny12)
– Enhanced Power-on Reset Circuit (ATtiny12)
– Internal Calibrated RC Oscillator (ATtiny12)
– Low-power, High-speed CMOS Process Technology
– Fully Static Operation
– Active: 2.2 mA
– Idle Mode: 0.5 mA
– Power-down Mode: <1 µA
– 8-pin PDIP and SOIC
– 1.8 - 5.5V for ATtiny12V-1
– 2.7 - 5.5V for ATtiny11L-2 and ATtiny12L-4
– 4.0 - 5.5V for ATtiny11-6 and ATtiny12-8
– 0 - 1.2 MHz (ATtiny12V-1)
– 0 - 2 MHz (ATtiny11L-2)
– 0 - 4 MHz (ATtiny12L-4)
– 0 - 6 MHz (ATtiny11-6)
– 0 - 8 MHz (ATtiny12-8)
In-System Programmable (ATtiny12)
Endurance: 1,000 Write/Erase Cycles (ATtiny11/12)
Endurance: 100,000 Write/Erase Cycles
GND
PDIP/SOIC
1
2
3
4
ATtiny11
®
RISC Architecture
8
7
6
5
VCC
PB2 (T0)
PB1 (INT0/AIN1)
PB0 (AIN0)
(RESET) PB5
(XTAL1) PB3
(XTAL2) PB4
GND
PDIP/SOIC
ATtiny12
1
2
3
4
8
7
6
5
VCC
PB2 (SCK/T0)
PB1 (MISO/INT0/AIN1)
PB0 (MOSI/AIN0)
Note: This is a summary document. A complete document
is available on our Web site at www.atmel.com.
8-bit
Microcontroller
with 1K Byte
Flash
ATtiny11
ATtiny12
Summary
Not recommended for new
design
Rev. 1006FS–AVR–06/07
1006FS–AVR–06/07
1

Related parts for ATTINY11L-2PI

ATTINY11L-2PI Summary of contents

Page 1

... Packages – 8-pin PDIP and SOIC • Operating Voltages – 1.8 - 5.5V for ATtiny12V-1 – 2.7 - 5.5V for ATtiny11L-2 and ATtiny12L-4 – 4.0 - 5.5V for ATtiny11-6 and ATtiny12-8 • Speed Grades – 1.2 MHz (ATtiny12V-1) – MHz (ATtiny11L-2) – MHz (ATtiny12L-4) – ...

Page 2

... All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. Table 1. Parts Description Device Flash EEPROM ATtiny11L 1K - ATtiny11 1K - ATtiny12V 1K ...

Page 3

... The device is manufactured using Atmel’s high-density nonvolatile memory technology. By combining an RISC 8-bit CPU with Flash on a monolithic chip, the Atmel ATtiny11 is a powerful microcontroller that provides a highly-flexible and cost-effective solution to many embedded control applications. ...

Page 4

... The device is manufactured using Atmel’s high-density nonvolatile memory technology. By combining an RISC 8-bit CPU with Flash on a monolithic chip, the Atmel ATtiny12 is a powerful microcontroller that provides a highly-flexible and cost-effective solution to many embedded control applications. ...

Page 5

Pin Descriptions VCC GND Port B (PB5..PB0) XTAL1 XTAL2 RESET 1006FS–AVR–06/07 Supply voltage pin. Ground pin. Port 6-bit I/O port. PB4..0 are I/O pins that can provide internal pull-ups (selected for each bit). On ATtiny11, PB5 is ...

Page 6

Register Summary ATtiny11 Address Name Bit 7 $3F SREG I $3E Reserved $3D Reserved $3C Reserved $3B GIMSK - $3A GIFR - $39 TIMSK - $38 TIFR - $37 Reserved $36 Reserved $35 MCUCR - $34 MCUSR - $33 TCCR0 ...

Page 7

Register Summary ATtiny12 Address Name Bit 7 $3F SREG I $3E Reserved $3D Reserved $3C Reserved $3B GIMSK - $3A GIFR - $39 TIMSK - $38 TIFR - $37 Reserved $36 Reserved $35 MCUCR - $34 MCUSR - $33 TCCR0 ...

Page 8

Instruction Set Summary Mnemonics Operands Description ARITHMETIC AND LOGIC INSTRUCTIONS ADD Rd, Rr Add two Registers ADC Rd, Rr Add with Carry two Registers SUB Rd, Rr Subtract two Registers SUBI Rd, K Subtract Constant from Register SBC Rd, Rr ...

Page 9

Instruction Set Summary (Continued) Mnemonics Operands Description DATA TRANSFER INSTRUCTIONS LD Rd,Z Load Register Indirect ST Z,Rr Store Register Indirect MOV Rd, Rr Move Between Registers LDI Rd, K Load Immediate IN Rd Port OUT P, Rr Out ...

Page 10

... Also Halide free and fully Green. 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S2 8-lead, 0.200" Wide, Plastic Gull-Wing Small Outline (EIAJ SOIC) ATtiny11/12 10 Ordering Code Package ATtiny11L-2PC 8P3 ATtiny11L-2SC 8S2 ATtiny11L-2PI 8P3 ATtiny11L-2SI 8S2 (2) ATtiny11L-2SU 8S2 ATtiny11-6PC 8P3 ATtiny11-6SC 8S2 ATtiny11-6PI 8P3 ...

Page 11

ATtiny12 Power Supply Speed (MHz) 1.8 - 5.5V 1.2 2.7 - 5.5V 4.0 - 5.5V Notes: 1. The speed grade refers to maximum clock rate when using an external crystal or external clock drive. The internal RC oscil- lator has ...

Page 12

Packaging Information 8P3 Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the ...

Page 13

Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs are not included recommended that upper ...

Page 14

Datasheet Revision History Rev. 1006F-06/07 Rev. 1006E-07/06 Rev. 1006D-07/03 Rev. 1006C-09/01 ATtiny11/12 14 Please note that the page numbers listed in this section are refering to this document. The revision numbers are referring to the document revision. 1. “Not recommended ...

Page 15

... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...

Related keywords