ATTINY13V-10SSI Atmel, ATTINY13V-10SSI Datasheet - Page 116

• Manufacturer Part Number: ATTINY13V-10SSI
• Description: IC MCU AVR 1K FLASH 10MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY13V-10SSI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Connectivity: -
• Lead Free Status / Rohs Status: No
• Other names: ATTINY13V-12SSI; ATTINY13V-12SSI

Table 18-1.
Notes:
116
Symbol
R
I
I
LIH
CC
PU
1. Typical values at +25°C.
2. “Max” means the highest value where the pin is guaranteed to be read as low.
3. Not tested in production.
4. “Min” means the lowest value where the pin is guaranteed to be read as high.
5. Although each I/O port can under non-transient, steady state conditions sink more than the test conditions, the sum of all I
6. Although each I/O port can under non-transient, steady state conditions source more than the test conditions, the sum of all
ATtiny13
(for all ports) should not exceed 60 mA. If I
not guaranteed to sink current greater than the listed test condition.
I
are not guaranteed to source current greater than the listed test condition.
Parameter
Input Leakage
Current I/O Pin
Pull-Up Resistor, I/O Pin
Pull-Up Resistor, Reset Pin
Supply Current,
Active Mode
Supply Current,
Idle Mode
Supply Current,
Power-Down Mode
OH
(for all ports) should not exceed 60 mA. If I
DC Characteristics, T
A
= -40°C to +85°C (Continued)
Condition
V
V
V
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
f = 1MHz, V
f = 4MHz, V
f = 8MHz, V
WDT enabled, V
WDT disabled, V
CC
CC
CC
= 5.5V, input low
= 5.5V, input low
= 5.5V, pin high
OL
CC
CC
CC
CC
CC
CC
exceeds the test condition, V
OH
= 2V
= 3V
= 5V
= 2V
= 3V
= 5V
CC
CC
exceeds the test condition, V
= 3V
= 3V
Min.
20
30
-1
OL
may exceed the related specification. Pins are
OH
Typ.
may exceed the related specification. Pins
0.08
0.41
0.3
1.6
1.6
0.5
5
5
(1)
Max.
0.35
1.8
0.2
50
80
10
1
6
1
3
2
2535J–AVR–08/10
Units
mA
mA
mA
mA
mA
mA
µA
kΩ
kΩ
µA
µA
OL