ATTINY13V-10SSI Atmel, ATTINY13V-10SSI Datasheet - Page 42

• Manufacturer Part Number: ATTINY13V-10SSI
• Description: IC MCU AVR 1K FLASH 10MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY13V-10SSI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 4 Channel
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Connectivity: -
• Lead Free Status / Rohs Status: No
• Other names: ATTINY13V-12SSI; ATTINY13V-12SSI

42
ATtiny13
This is useful for keeping the Watchdog Timer security while using the interrupt. To stay in Inter-
rupt and System Reset Mode, WDTIE must be set after each interrupt. This should however not
be done within the interrupt service routine itself, as this might compromise the safety-function of
the Watchdog System Reset mode. If the interrupt is not executed before the next time-out, a
System Reset will be applied.
Table 8-1.
Note:
• Bit 4 - WDCE: Watchdog Change Enable
This bit is used in timed sequences for changing WDE and prescaler bits. To clear the WDE bit,
and/or change the prescaler bits, WDCE must be set.
Once written to one, hardware will clear WDCE after four clock cycles.
• Bit 3 - WDE: Watchdog System Reset Enable
WDE is overridden by WDRF in MCUSR. This means that WDE is always set when WDRF is
set. To clear WDE, WDRF must be cleared first. This feature ensures multiple resets during con-
ditions causing failure, and a safe start-up after the failure.
• Bit 5, 2:0 - WDP[3:0]: Watchdog Timer Prescaler 3, 2, 1 and 0
The WDP[3:0] bits determine the Watchdog Timer prescaling when the Watchdog Timer is run-
ning. The different prescaling values and their corresponding time-out periods are shown in
Table 8-2 on page
Table 8-2.
WDP3
WDTON
0
0
0
0
0
0
0
0
1
1
1
1
1
1
0
1. WDTON fuse set to “0“ means programmed and “1“ means unprogrammed.
(1)
WDP2
0
0
0
0
1
1
1
1
0
0
Watchdog Timer Configuration
Watchdog Timer Prescale Select
WDE
42..
0
0
1
1
x
WDP1
0
0
1
1
0
0
1
1
0
0
WDP0
WDTIE
0
1
0
1
0
1
0
1
0
1
0
1
0
1
x
Number of WDT Oscillator
Mode
Stopped
Interrupt Mode
System Reset Mode
Interrupt and System Reset
Mode
System Reset Mode
1024K (1048576) cycles
128K (131072) cycles
256K (262144) cycles
512K (524288) cycles
16K (16384) cycles
32K (32768) cycles
64K (65536) cycles
2K (2048) cycles
4K (4096) cycles
8K (8192) cycles
Cycles
Action on Time-out
None
Interrupt
Reset
Interrupt, then go to System
Reset Mode
Reset
Typical Time-out at
V
CC
0.125 s
16 ms
32 ms
64 ms
0.25 s
0.5 s
1.0 s
2.0 s
4.0 s
8.0 s
= 5.0V
2535J–AVR–08/10