MC68HC908GZ8MFJ Freescale Semiconductor, MC68HC908GZ8MFJ Datasheet - Page 176

• Manufacturer Part Number: MC68HC908GZ8MFJ
• Description: IC MCU 8K FLASH 8MHZ CAN 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC68HC908GZ8MFJ

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: CAN, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

Resets and Interrupts
14.3.2.3 IRQ Pin
A logic 0 on the IRQ1 pin latches an external interrupt request.
14.3.2.4 Clock Generator (CGM)
The CGM can generate a CPU interrupt request every time the phase-locked loop circuit (PLL) enters or
leaves the locked state. When the LOCK bit changes state, the PLL flag (PLLF) is set. The PLL interrupt
enable bit (PLLIE) enables PLLF CPU interrupt requests. LOCK is in the PLL bandwidth control register.
PLLF is in the PLL control register.
14.3.2.5 Timer Interface Module 1 (TIM1)
TIM1 CPU interrupt sources:
14.3.2.6 Timer Interface Module 2 (TIM2)
TIM2 CPU interrupt sources:
14.3.2.7 Serial Peripheral Interface (SPI)
SPI CPU interrupt sources:
176
•
•
•
•
•
•
•
TIM1 overflow flag (TOF) — The TOF bit is set when the TIM1 counter value rolls over to $0000
after matching the value in the TIM1 counter modulo registers. The TIM1 overflow interrupt enable
bit, TOIE, enables TIM1 overflow CPU interrupt requests. TOF and TOIE are in the TIM1 status
and control register.
TIM1 channel flags (CH1F–CH0F) — The CHxF bit is set when an input capture or output compare
occurs on channel x. The channel x interrupt enable bit, CHxIE, enables channel x TIM1 CPU
interrupt requests. CHxF and CHxIE are in the TIM1 channel x status and control register.
TIM2 overflow flag (TOF) — The TOF bit is set when the TIM2 counter value rolls over to $0000
after matching the value in the TIM2 counter modulo registers. The TIM2 overflow interrupt enable
bit, TOIE, enables TIM2 overflow CPU interrupt requests. TOF and TOIE are in the TIM2 status
and control register.
TIM2 channel flags (CH1F–CH0F) — The CHxF bit is set when an input capture or output compare
occurs on channel x. The channel x interrupt enable bit, CHxIE, enables channel x TIM2 CPU
interrupt requests. CHxF and CHxIE are in the TIM2 channel x status and control register.
SPI receiver full bit (SPRF) — The SPRF bit is set every time a byte transfers from the shift register
to the receive data register. The SPI receiver interrupt enable bit, SPRIE, enables SPRF CPU
interrupt requests. SPRF is in the SPI status and control register and SPRIE is in the SPI control
register.
SPI transmitter empty (SPTE) — The SPTE bit is set every time a byte transfers from the transmit
data register to the shift register. The SPI transmit interrupt enable bit, SPTIE, enables SPTE CPU
interrupt requests. SPTE is in the SPI status and control register and SPTIE is in the SPI control
register.
Mode fault bit (MODF) — The MODF bit is set in a slave SPI if the SS pin goes high during a
transmission with the mode fault enable bit (MODFEN) set. In a master SPI, the MODF bit is set if
the SS pin goes low at any time with the MODFEN bit set. The error interrupt enable bit, ERRIE,
enables MODF CPU interrupt requests. MODF, MODFEN, and ERRIE are in the SPI status and
control register.
MC68HC908GZ16 • MC68HC908GZ8 Data Sheet, Rev. 4
Freescale Semiconductor