C8051F236 Silicon Laboratories Inc, C8051F236 Datasheet - Page 20

• Manufacturer Part Number: C8051F236
• Description: IC 8051 MCU 8K FLASH 48TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F2xxr

Specifications of C8051F236

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 32
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Data Converters: -

C8051F2xx
1.5.
The C8051F206, C8051F220/1/6 and C8051F230/1/6 include a Full-Duplex UART and SPI Bus. Each of
the serial buses is fully implemented in hardware and makes extensive use of the CIP-51's interrupts, thus
requiring very little intervention by the CPU. The serial buses do not have to "share" resources such as
timers, interrupts, or Port I/O, so both of the serial buses may be used simultaneously. (You may use
Timer1, Timer 2, or SYSCLK to generate baud rates for UART).
1.6.
The C8051F220/1/6 has an on-chip 8-bit SAR ADC and the C8051F206 has a 12-bit SAR ADC with a pro-
grammable gain amplifier. With a maximum throughput of 100ksps, the ADC offers true 8-bit with an INL of
±1/4 LSB, and or 12-bit accuracy with ±2 LSB. The voltage reference can be the power supply (
an external reference voltage (VREF). Also, the system controller can place the ADC into a power-saving
shutdown mode when not in use. A programmable gain amplifier follows the analog multiplexer. The gain
can be set in software from 0.5 to 16 in powers of 2.
Conversions can be initiated in two ways; a software command or an overflow on Timer 2. This flexibility
allows the start of conversion to be triggered by software events, or convert continuously. A completed
conversion causes an interrupt, or a status bit can be polled in software to determine the end of conver-
sion. The resulting 8-bit data word is latched into an SFR upon completion of a conversion.
20
Comparators
INT0 & INT1
Serial Ports
Analog to Digital Converter
ADC
T0,T1,T2
SYSCLK
External
Timers
UART
0 & 1
SPI
Figure 1.9. Port I/O Functional Block Diagram
M
A
U
X
Registers
PRTnMX
MUX
MUX
Port
MUX
Port
Port
0
1
2
Rev. 1.6
Port0 I/O Cell
Port1 I/O Cell
Port2 I/O Cell
Port3 I/O Cell
PRTnCF &
PnMODE
registers
External
P0.0/TX
P0.1/RX
P0.2/INT0
P0.3/INT1
P0.4/T0
P0.5/T1
P0.6/T2
P0.7/T2EX
P1.0/CP0+
P1.1/CP0-
P1.2/CP0
P1.3/CP1+
P1.4/CP1-
P1.5/CP1
P1.6/SYSCLK
P1.7
P2.0/SCK
P2.1/MISO
P2.2/MOSI
P2.3/NSS
P2.4
P2.5
P2.6
P2.7
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
pins
configured via software as an
analog input to the ADC
Any port pin may be
V
DD ), or