MC908QL4MDTE Freescale Semiconductor, MC908QL4MDTE Datasheet - Page 205

• Manufacturer Part Number: MC908QL4MDTE
• Description: IC MCU 8BIT 4K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QL4MDTE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN (Local Interconnect Network)
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Freescale Semiconductor
Input low voltage
Input hysteresis
DC injection current
Ports Hi-Z leakage current
Capacitance
POR rearm voltage
POR rise time ramp rate
Monitor mode entry voltage
Pullup resistors
Pulldown resistors
Low-voltage inhibit reset, trip falling voltage
Low-voltage inhibit reset, trip rising voltage
Low-voltage inhibit reset/recover hysteresis
1. V
2. Typical values reflect average measurements at midpoint of voltage range, 25•C only.
3. This parameter is characterized and not tested on each device.
4. All functional non-supply pins are internally clamped to V
5. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor,
6. Power supply must maintain regulation within operating V
7. If minimum V
8. R
9. R
PTA0–PTA5, PTB0–PTB7
Single pin limit
Total MCU limit, includes sum of all stressed pins
Ports (as input)
PTA0–PTA5, PTB0–PTB7
PTA0–PTA5
V
V
V
V
calculate resistance values for positive and negative clamp voltages, then use the larger of the two values.
conditions. If positive injection current (V
result in external power supply going out of regulation. Ensure external V
injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock
is present, or if clock rate is very low (which would reduce overall power consumption).
V
in
in
in
in
DD
DD
PU
PD
> V
< V
> V
< V
is measured at V
is measured at V
= 4.5 to 5.5 Vdc, V
is reached.
DD
SS
DD
SS
(8)
(3)
DD
(3)
(9)
(3) (4) (5) (6)
Characteristic
is not reached before the internal POR reset is released, the LVI will hold the part in reset until minimum
(3)(7)
DD
DD
SS
(3)
= 5.0 V. Pullup resistors only available when PTAPUEx is enabled with KBIPx = 0.
= 5.0 V, Pulldown resistors only available when PTAPUEx is enabled with KBIPx =1.
= 0 Vdc, T
(1)
A
= T
MC68HC908QL4 Data Sheet, Rev. 8
in
L
> V
to T
DD
H
) is greater than I
, unless otherwise noted.
SS
DD
Symbol
V
V
V
R
V
V
V
and V
range during instantaneous and operating maximum current
R
R
TRIPF
TRIPR
C
V
HYS
I
I
POR
POR
HYS
TST
IC
IL
PU
PD
IN
IL
DD
DD
, the injection current may flow out of V
.
DD
0.06 x V
V
DD
0.035
load will shunt current greater than maximum
3.90
4.00
Min
V
750
16
16
—
—
0
0
0
0
0
SS
+ 2.5
DD
5-V DC Electrical Characteristics
Typ
4.20
4.30
100
26
26
—
—
—
—
—
—
—
—
—
—
—
(2)
0.3 x V
Max
–0.2
4.50
4.60
9.1
25
–5
±1
36
36
—
—
—
—
2
8
DD
DD
and could
V/ms
Unit
mA
mV
mV
μA
kΩ
kΩ
pF
V
V
V
V
V
205