MCP6S21-I/SN Microchip Technology, MCP6S21-I/SN Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP6S21-I/SN
Manufacturer Part Number
MCP6S21-I/SN
Description
IC PGA 1CH R-R I/O 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.MCP6S22DM-PICTL.pdf
(43 pages)
Specifications of MCP6S21-I/SN
Package / Case
8-SOIC (3.9mm Width)
Amplifier Type
Programmable Gain
Number Of Circuits
1
Output Type
Rail-to-Rail
Slew Rate
22 V/µs
-3db Bandwidth
12MHz
Current - Input Bias
1pA
Voltage - Input Offset
275µV
Current - Supply
1mA
Current - Output / Channel
30mA
Voltage - Supply, Single/dual (±)
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Number Of Channels
1
Available Set Gain
30.1 dB (Typ)
Input Offset Voltage
0.275 mV @ 5.5 V
Input Bias Current (max)
0.000001 uA (Typ) @ 5.5 V
Operating Supply Voltage
3 V or 5 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Gain Bandwidth Product
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCP6S21-I/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
4.2.2
The input stage of the internal op amp uses two differ-
ential input stages in parallel; one operates at low V
(input voltage), while the other operates at high V
With this topology, the internal inputs can operate to
0.3V past either supply rail. The input offset voltage is
measured at both V
ensure proper operation.
The transition between the two input stages occurs
when V
linearity, avoid this region of operation.
4.2.3
The Maximum Output Voltage Swing is the maximum
swing possible under a particular output load. Accord-
ing to the specification table, the output can reach
within 60 mV of either supply rail when R
V
4.2.4
The
devices. It is designed to not exhibit phase inversion
when the input pins exceed the supply voltages.
Figure 2-34 shows an input voltage exceeding both
supplies with no resulting phase inversion.
The maximum voltage that can be applied to the input
pins (CHX) is V
inputs that exceed this absolute maximum rating can
cause excessive current to flow in or out of the input
pins. Current beyond ±2 mA can cause possible reli-
ability problems. Applications that exceed this rating
must be externally limited with an input resistor, as
shown in Figure 4-2.
FIGURE 4-2:
into an input pin.
under other conditions.
REF
2003 Microchip Technology Inc.
V
IN
= V
amplifier family is designed with CMOS input
IN
DD
R
R
IN
IN
RAIL-TO-RAIL INPUT
RAIL-TO-RAIL OUTPUT
/2. See Figure 2-21 for typical performance
INPUT VOLTAGE AND PHASE
REVERSAL
V
R
DD
------------------------------------------------------------------------------ -
SS
IN
V
--------------------------------------------------------------------------- -
Maximum expected V
- 1.5V. For the best distortion and gain
SS
- 0.3V to V
CHX
–
IN
Minimum expected V
= V
R
IN
MCP6S2X
SS
limits the current flow
2 mA
2 mA
DD
- 0.3V and V
+ 0.3V. Voltages on the
IN
–
L
V
IN
DD
= 10 k and
DD
+ 0.3V to
V
OUT
IN
IN
.
4.3
The resistor ladder shown in Figure 4-1 (R
R
with the inverting input reduces the parasitic capaci-
tance, distortion and gain mismatch.
R
causes additional current draw from the supplies.
In Shutdown mode, R
and V
fier’s inverting input are all connected through R
and the output is not high-Z (unlike the external op
amp).
While R
small. Refer to Figure 2-12.
4.4
These PGAs use a software shutdown command.
When the SPI interface sends a shutdown command,
the internal op amp is shut down and its output placed
in a high-Z state.
The resistive ladder is always connected between
V
output resistance will be on the order of 5 k and there
will be a path for output signals to appear at the input.
The Power-on Reset (POR) circuitry will temporarily
place the part in shutdown when activated. See
Section 5.4, “Power-On Reset”, for details.
REF
G
LAD
) sets the gain. Placing the gain switches in series
is an additional load on the output of the PGA and
and V
REF
LAD
Resistor Ladder
Shutdown Mode
pins. Thus, these pins and the internal ampli-
OUT
contributes to the output noise, its effect is
; even in shutdown. This means that the
MCP6S21/2/6/8
LAD
is still attached to the OUT
DS21117A-page 17
LAD
= R
LAD
F
+