LT1800CS5#TRMPBF Linear Technology, LT1800CS5#TRMPBF Datasheet - Page 18

• Manufacturer Part Number: LT1800CS5#TRMPBF
• Description: IC OPAMP R-RIN/OUT LP TSOT-23-5
• Manufacturer: Linear Technology

Specifications of LT1800CS5#TRMPBF

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 23 V/µs
• Gain Bandwidth Product: 70MHz
• Current - Input Bias: 400nA
• Voltage - Input Offset: 1000µV
• Current - Supply: 1.8mA
• Current - Output / Channel: 50mA
• Voltage - Supply, Single/dual (±): 2.3 V ~ 12.6 V, ±1.15 V ~ 6.3 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: TSOT-23-5, TSOT-5, TSOP-5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Other names: LT1800CS5#TRMPBFTR

V
IN
LT1800
TYPICAL APPLICATION
Low Power High Voltage Amplifi er
Certain materials used in optical applications have charac-
teristics that change due to the presence and strength of a
DC electric fi eld. The voltage applied across these materials
should be precisely controlled to maintain desired proper-
ties, sometimes as high as 100’s of volts. The materials
are not conductive and represent a capacitive load.
The circuit of Figure 6 shows the LT1800 used in an ampli-
fi er capable of a 250V output swing and providing precise
150V
RELATED PARTS
PART NUMBER
LT1399
LT1498/LT1499
LT1630/LT1631
LT1801/LT1802
LT1806/LT1807
LT1809/LT1810
C-Load is a trademark of Linear Technology Corporation.
18
8pF
C2
0.1 F
R2
2k
R1
2k
Figure 6. Low Power, High Voltage Amplifi er
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
[phone]
R3
200k
+
–
LT1800
39pF
DESCRIPTION
Triple 300MHz Current Feedback Amplifi er
Dual/Quad 10MHz, 6Vμs Rail-to-Rail Input and Output C-Load™ Op Amps High DC Accuracy, 475μV V
Dual/Quad 30MHz, 10V/μs Rail-to-Rail Input and Output Op Amps
80MHz, 25V/μs Low Power Rail-to-Rail Input/Output Precision Op Amps
Single/Dual 325MHz, 140V/μs Rail-to-Rail Input and Output Op Amps
Single/Dual 180MHz Rail-to-Rail Input/Output Op Amps
5V
C1
●
FAX: [phone]
Q1
Q3
5V
10k
10k
R4
R5
2k
2k
Q5
Q7
Q2
Q4
4.99k
4.99k
–130V
130V
5V
R6
2k
R7
2k
Q6
Q8
1800 F06
●
1k
1k
www.linear.com
A
±130V SUPPLY I
OUTPUT SWING = ±128.8V
OUTPUT OFFSET 20mV
OUTPUT SHORT-CIRCUIT CURRENT 3mA
10% TO 90% RISE TIME 8 s, 200V OUTPUT STEP
SMALL-SIGNAL BANDWIDTH 150kHz
Q1, Q2, Q7, Q8: ON SEMI MPSA42
Q3, Q4, Q5, Q6: ON SEMI MPSA92
V
V
OUT
= V
MATERIAL UNDER
ELECTRIC FIELD
100pF
OUT
/V
IN
= –100
Q
= 130 A
DC output voltage. When no signal is present, the op
amp output sits at about mid-supply. Transistors Q1 and
Q3 create bias voltages for Q2 and Q4, which are forced
into a low quiescent current by degeneration resistors
R4 and R5. When a transient signal arrives at V
amp output moves and causes the current in Q2 or Q4
to change depending on the signal polarity. The current,
limited by the clipping of the LT1800 output and the 3kΩ
of total emitter degeneration, is mirrored to the output
devices to drive the capacitive load. The LT1800 output
then returns to near mid-supply, providing the precise DC
output voltage to the load. The attention to limit the current
of the output devices minimizes power dissipation thus
allowing for dense layout, and inherits better reliability.
Figure 7 shows the time domain response of the amplifi er
providing a 200V output swing into a 100pF load.
COMMENTS
0.1dB Gain Flatness to 150MHz, Shutdown
Max Supply Current 2.2mA per Amp
High DC Accuracy, 525μV V
Max Supply Current 4.4mA per Amplifi er
Dual/Quad Version of the LT1800
High DC Accuracy, 550μV V
Low Distortion –80dB at 5MHz, Power-Down (LT1806)
350V/μs Slew Rate, Low Distortion –t at 5MHz,
Power-Down (LT1809)
50V/DIV
2V/DIV
V
OUT
V
IN
Figure 7. Large-Signal Time Domain
Response of the Amplifi er
© LINEAR TECHNOLOGY CORPORATION 2009
10μs/DIV
OS(MAX)
OS(MAX)
OS(MAX)
LT 0709 REV A • PRINTED IN USA
, 4mV/°C Max Drift,
, 70mA Output Current,
, Low Noise 3.5nV/√Hz,
1800 F07
IN
, the op
1800fa