AD8571ARZ Analog Devices Inc, AD8571ARZ Datasheet - Page 19

• Manufacturer Part Number: AD8571ARZ
• Description: IC OPAMP CHOPPER R-R 30MA 8SOIC
• Manufacturer: Analog Devices Inc
• Type: Chopper Stabilizationr

Specifications of AD8571ARZ

• Slew Rate: 0.4 V/µs
• Amplifier Type: Chopper (Zero-Drift)
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 1.5MHz
• Current - Input Bias: 10pA
• Voltage - Input Offset: 1µV
• Current - Supply: 850µA
• Current - Output / Channel: 30mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: Zero Drift
• No. Of Amplifiers: 1
• Bandwidth: 1.5MHz
• Supply Voltage Range: 2.7V To 5V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Rail/rail I/o Type: Rail to Rail Input/Output
• Number Of Elements: 1
• Unity Gain Bandwidth Product: 1.5MHz
• Common Mode Rejection Ratio: 120dB
• Input Offset Voltage: 5uV
• Input Bias Current: 50pA
• Single Supply Voltage (typ): 3V
• Dual Supply Voltage (typ): Not RequiredV
• Voltage Gain In Db: 145dB
• Power Supply Rejection Ratio: 120dB
• Power Supply Requirement: Single
• Shut Down Feature: No
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Technology: CMOS
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Compliant

CAPACITIVE LOAD DRIVE
The AD857x have excellent capacitive load driving capabilities
and can safely drive up to 10 nF from a single 5 V supply.
Although the device is stable, capacitive loading limits the
bandwidth of the amplifier. Capacitive loads also increase the
amount of overshoot and ringing at the output. The RC snubber
network shown in Figure 59 can be used to reduce the capacitive
load ringing and overshoot.
Although the snubber network does not recover the loss of
amplifier bandwidth from the load capacitance, it does allow
the amplifier to drive larger values of capacitance while
maintaining a minimum of overshoot and ringing. Figure 60
shows the output of an AD857x driving a 1 nF capacitor with
and without a snubber network.
Figure 59. Snubber Network Configuration for Driving Capacitive Loads
SNUBBER
SNUBBER
WITHOUT
Figure 60. Overshoot and Ringing Are Substantially Reduced Using
WITH
200mV p-p
V
IN
10μs
–
+
a Snubber Network
V
C
5V
S
L
= 5V
= 4.7nF
Rx
60Ω
Cx
0.47µF
AD8571/
AD8572/
AD8574
C
4.7nF
L
100mV
V
OUT
Rev. E | Page 19 of 24
The optimum value for the resistor and capacitor is a function
of the load capacitance and is best determined empirically
because actual C
substantially from the nominal capacitive load. Table 5 shows
some snubber network values that can be used as starting points.
Table 5. Snubber Network Values for Driving Capacitive Loads
C
1
4.7
10
POWER-UP BEHAVIOR
At power-up, the AD857x settles to a valid output within 5 μs.
Figure 61 shows an oscilloscope photo of the output of the
amplifier along with the power supply voltage. Figure 62 shows
the test circuit. With the amplifier configured for unity gain, the
device takes approximately 5 μs to settle to its final output
voltage, hundreds of microseconds faster than many other
autocorrection amplifiers.
L
(nF)
V
OUT
V+
0V
0V
BOTTOM TRACE = 2V/DIV
TOP TRACE = 1V/DIV
100kΩ
100kΩ
Figure 62. AD857x Test Circuit for Power-Up Time
Figure 61. AD857x Output Behavior at Power-Up
L
5µs
includes stray capacitances and can differ
Rx (Ω)
200
60
20
AD8571/AD8572/AD8574
AD8571/
AD8572/
AD8574
V
Cx
1 nF
0.47 μF
10 μF
SY
= 0V TO 5V
1V
V
OUT