AD8616ARZ Analog Devices Inc, AD8616ARZ Datasheet - Page 12

• Manufacturer Part Number: AD8616ARZ
• Description: IC OPAMP GP R-R CMOS 24MHZ 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD8616ARZ

• Slew Rate: 12 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 24MHz
• Current - Input Bias: 0.2pA
• Voltage - Input Offset: 23µV
• Current - Supply: 1.7mA
• Current - Output / Channel: 150mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: Precision
• No. Of Amplifiers: 1
• Bandwidth: 24MHz
• Supply Voltage Range: 2.7V To 5V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Operating Temperature Range: -40°C To +125°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD8615/AD8616/AD8618
OVERLOAD RECOVERY TIME
Overload recovery time is the time it takes the output of the
amplifier to come out of saturation and recover to its linear region.
Overload recovery is particularly important in applications where
small signals must be amplified in the presence of large transients.
Figure 40 and Figure 41 show the positive and negative overload
recovery times of the AD8616. In both cases, the time elapsed
before the AD8616 comes out of saturation is less than 1 μs. In
addition, the symmetry between the positive and negative recovery
times allows excellent signal rectification without distortion to the
output signal.
D/A CONVERSION
The AD8616 can be used at the output of high resolution DACs.
The low offset voltage, fast slew rate, and fast settling time make
the part suitable to buffer voltage output or current output
DACs.
Figure 42 shows an example of the AD8616 at the output of the
AD5542. The AD8616’s rail-to-rail output and low distortion
help maintain the accuracy needed in data acquisition systems
and automated test equipment.
0V
0V
0V
0V
V
R
A
V
+50mV
–50mV
S
IN
+2.5V
L
V
– 2.5V
= ±2.5V
= 10kΩ
= 100
= 50mV
Figure 41. Negative Overload Recovery
Figure 40. Positive Overload Recovery
TIME (1µs/DIV)
TIME (1µs/DIV)
V
R
A
V
S
IN
L
V
= ±2.5V
= 10kΩ
= 100
= 50mV
Rev. E | Page 12 of 20
INTERFACE
LOW NOISE APPLICATIONS
Although the AD8618 typically has less than 8 nV/√Hz of voltage
noise density at 1 kHz, it is possible to reduce it further. A simple
method is to connect the amplifiers in parallel, as shown in
Figure 43. The total noise at the output is divided by the square
root of the number of amplifiers. In this case, the total noise is
approximately 4 nV/√Hz at room temperature. The 100 Ω
resistor limits the current and provides an effective output
resistance of 50 Ω.
SERIAL
V
IN
0.1 µF
CS
DIN
SCLK
LDAC
V
5V
DD
DGND
Figure 42. Buffering DAC Output
2.5V
REFF
AD5542
Figure 43. Noise Reduction
10Ω
10Ω
0.1µF
10Ω
10Ω
R10
R4
R1
R7
10µF
AGND
+
REFS
3
3
2
3
3
2
2
2
V+
V+
V+
V–
V–
V+
V–
V–
V
1kΩ
1kΩ
1kΩ
1kΩ
R11
R5
R2
R8
OUT
1
1
1
1
1/2
AD8616
100Ω
100Ω
100Ω
100Ω
R12
R6
R9
R3
UNIPOLAR
V
OUTPUT
OUT