AD712JRZ Analog Devices Inc, AD712JRZ Datasheet - Page 17

• Manufacturer Part Number: AD712JRZ
• Description: IC OPAMP BIFET DUAL PREC 8SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD712JRZ

• Slew Rate: 20 V/µs
• Amplifier Type: J-FET
• Number Of Circuits: 2
• -3db Bandwidth: 4MHz
• Current - Input Bias: 25pA
• Voltage - Input Offset: 300µV
• Current - Supply: 5mA
• Current - Output / Channel: 25mA
• Voltage - Supply, Single/dual (±): 9 V ~ 36 V, ±4.5 V ~ 20 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: High Speed
• No. Of Amplifiers: 2
• Bandwidth: 4MHz
• Supply Voltage Range: ± 4.5V To ± 18V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Operating Temperature Range: 0°C To +70°C
• Rail/rail I/o Type: No
• Number Of Elements: 2
• Unity Gain Bandwidth Product: 3MHz
• Common Mode Rejection Ratio: 70dB
• Input Offset Voltage: 3@±15VmV
• Input Bias Current: 100pA
• Single Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (typ): ±15V
• Voltage Gain In Db: 112.04dB
• Power Supply Requirement: Dual
• Shut Down Feature: No
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): ±4.5V
• Dual Supply Voltage (max): ±18V
• Technology: BiFET
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Compliant

FILTERS
ACTIVE FILTER APPLICATIONS
In active filter applications using op amps, the dc accuracy of
the amplifier is critical to optimal filter performance. The
amplifier offset voltage and bias current contribute to output
error. Offset voltage is passed by the filter and can be amplified
to produce excessive output offset. For low frequency applications
requiring large value input resistors, bias currents flowing
through these resistors also generate an offset voltage.
In addition, at higher frequencies, the op amp dynamics must
be carefully considered. Here, slew rate, bandwidth, and open-
loop gain play a major role in op amp selection. The slew rate
must be fast as well as symmetrical to minimize distortion. The
amplifier bandwidth in conjunction with the filter gain dictates
the frequency response of the filter.
The use of a high performance amplifier such as the AD712
minimizes both dc and ac errors in all active filter applications.
SECOND-ORDER LOW-PASS FILTER
Figure 48 depicts the AD712 configured as a second-order,
Butterworth low-pass filter. With the values as shown, the
corner frequency is 20 kHz; however, the wide bandwidth of the
AD712 permits a corner frequency as high as several hundred
kilohertz. Equations for component selection are as follows:
R1 = R2 = A user selected value (10 kΩ to 100 kΩ, typical)
C1 (in farads) =
C
2
=
( )
2
π
(
. 0
f
cutoff
707
)
( )
( )
2
R
π
1
(
. 1
f
cutoff
414
)
( )
R
1
Rev. H | Page 17 of 20
An important property of filters is their out-of-band rejection.
The simple 20 kHz low-pass filter shown in Figure 48, can be
used to condition a signal contaminated with clock pulses or
sampling glitches that have considerable energy content at high
frequencies.
The low output impedance and high bandwidth of the AD712
minimize high frequency feedthrough as shown in Figure 49.
The upper trace is that of another low cost BiFET op amp
showing 17 dB more feedthrough at 5 MHz.
CENTER 5 000 000.0Hz
RBW 30kHz
REF 20.0 dBm
10dB/DIV
V
IN
20kΩ
R1
Figure 48. Second-Order Low-Pass Filter
Figure 49. High Frequency Feedthrough
TYPICAL BIFET
280pF
20kΩ
R2
C2
RANGE 15.0dBm
560pF
VBW 30kHz
C1
+
–
AD712
+15V
–15V
1/2
AD712
0.1µF
0.1µF
SPAN 10 000 000.0Hz
OFFSET .0 Hz
ST .8 SEC
0dB
V
OUT
AD712