LMH6618MK/NOPB National Semiconductor, LMH6618MK/NOPB Datasheet - Page 25

• Manufacturer Part Number: LMH6618MK/NOPB
• Description: IC OP AMP SGL VF RRIO TSOT23-6
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of LMH6618MK/NOPB

• Amplifier Type: Voltage Feedback
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Slew Rate: 57 V/µs
• Gain Bandwidth Product: 65MHz
• -3db Bandwidth: 140MHz
• Current - Input Bias: 1.5µA
• Voltage - Input Offset: 100µV
• Current - Supply: 1.35mA
• Current - Output / Channel: 35mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 11 V, ±1.35 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: TSOT-23-6, TSOT-6
• For Use With: 551600083-001 - BOARD FOR SOT23 LMH6611/18
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LMH6618MK; LMH6618MK; LMH6618MKTR

Note:
GBWP = 65 MHz
C
C
V
Figure 12 shows the frequency response for the various pho-
todiodes in Table 3.
FIGURE 12. Frequency Response for Various Photodiode
When analyzing the noise at the output of the TIA, it is im-
portant to note that the various noise sources (i.e. op amp
S
T
IN
= C
= ±2.5V
= 2 pF
PD
(pF)
C
100
222
22
47
+ C
PD
IN
and Feedback Capacitors
(pF)
102
224
C
24
49
T
TABLE 3. TIA (Figure 1) Compensation and Performance Results
C
10.9
15.8
23.4
(pF)
F CAL
7.7
20195868
C
F USED
(pF)
5.6
10
15
18
25
noise voltage, feedback resistor thermal noise, input noise
current, photodiode noise current) do not all operate over the
same frequency band. Therefore, when the noise at the out-
put is calculated, this should be taken into account. The op
amp noise voltage will be gained up in the region between the
noise gain’s zero and pole (f
the values of R
starts and therefore its contribution to the total output noise
will be larger. It is obvious to note that it is advantageous to
minimize C
reverse bias across the diode at the expense of excess dark
current and noise.
DIFFERENTIAL CABLE DRIVER FOR NTSC VIDEO
The LMH6618 and LMH6619 can be used to drive an NTSC
video signal on a twisted-pair cable. Figure 13 shows the
schematic of a differential cable driver for NTSC video. This
circuit can be used to transmit the signal from a camera over
a twisted pair to a monitor or display located a distance. C
and C
LMH6619. The two amplifiers of the LMH6619 are set to a
gain of 2 to compensate for the 75Ω back termination resistors
on the outputs. The LMH6618 is set to a gain of 1. Because
of the DC bias the output of the LMH6618 is AC coupled. Most
monitors and displays will accept AC coupled inputs.
2
are used to AC couple the video signal into the
f
−3 dB CAL
(MHz)
IN
23.7
16.6
11.5
7.81
by proper choice of op amp or by applying a
F
and C
T
, the sooner the noise gain peaking
f
Z
−3 dB MEAS
and f
(MHz)
15.2
10.8
20
8
P
in Figure 11). The higher
Peaking
www.national.com
(dB)
0.9
0.8
0.9
2.9
1