ISL28274FAZ-T7 Intersil, ISL28274FAZ-T7 Datasheet - Page 17
![IC INSTR/OP AMP RRIO SGL 16-QSOP](/photos/12/50/125097/isl28274faz-t7_sml.jpg)
ISL28274FAZ-T7
Manufacturer Part Number
ISL28274FAZ-T7
Description
IC INSTR/OP AMP RRIO SGL 16-QSOP
Manufacturer
Intersil
Datasheet
1.ISL28474EVAL1Z.pdf
(18 pages)
Specifications of ISL28274FAZ-T7
Amplifier Type
Instrumentation
Number Of Circuits
2
Output Type
Rail-to-Rail
Slew Rate
0.5 V/µs
Gain Bandwidth Product
6MHz
Current - Input Bias
10pA
Voltage - Input Offset
35µV
Current - Supply
120µA
Current - Output / Channel
31mA
Voltage - Supply, Single/dual (±)
2.4 V ~ 5 V, ±1.2 V ~ 2.5 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
16-QSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
-3db Bandwidth
-
Other names
ISL28274FAZ-T7
ISL28274FAZ-T7TR
ISL28274FAZ-T7TR
A finite resistance R
output offset of VIN*(R
approaches zero, the gain equation is simplified to Equation 3
for Figure 63. VOUT is simply shifted by an amount VREF.
External Resistor Mismatches
Because of the independent pair of feedback terminals
provided by the ISL28274, the CMRR is not degraded by
any resistor mismatches. Hence, unlike a three op amp and
especially a two op amp in-amp, the ISL28274 reduces the
cost of external components by allowing the use of 1% or
more tolerance resistors without sacrificing CMRR
performance. The ISL28274 CMRR will be 100dB
regardless of the tolerance of the resistors used.
Using Only the Instrumentation Amplifier
If the application only requires the instrumentation amp, the
user must configure the unused op amp to prevent it from
oscillating. The unused op amp will oscillate if the input and
output pins are floating. This will result in higher than
expected supply currents and possible noise injection into
the in-amp. The proper way to prevent this oscillation is to
short the output to the negative input and ground the positive
input (as shown in Figure 64).
Proper Layout Maximizes Performance
To achieve the maximum performance of the high input
impedance and low offset voltage, care should be taken in
the circuit board layout. The PC board surface must remain
clean and free of moisture to avoid leakage currents
between adjacent traces. Surface coating of the circuit board
will reduce surface moisture and provide a humidity barrier,
reducing parasitic resistance on the board. When input
leakage current is a concern, the use of guard rings around
the amplifier inputs will further reduce leakage currents.
Figure 65 shows a guard ring example for a unity gain
amplifier that uses the low impedance amplifier output at the
same voltage as the high impedance input to eliminate
surface leakage. The guard ring does not need to be a
specific width, but it should form a continuous loop around
both inputs. For further reduction of leakage currents,
components can be mounted to the PC board using Teflon
standoff insulators.
VOUT
FIGURE 64. PREVENTING OSCILLATIONS IN UNUSED
=
⎛
⎜
⎝
1
+
------- -
R
R
CHANNELS
G
F
⎞
⎟
⎠
(
VIN
S
in series with the VREF source, adds an
S
)
/R
+
(
G
VREF
+
-
). As the series resistance R
17
)
ISL28274, ISL28474
(EQ. 3)
S
Current Limiting
The ISL28274 has no internal current-limiting circuitry. If the
output is shorted, it is possible to exceed the Absolute
Maximum Rating for output current or power dissipation,
potentially resulting in the destruction of the device.
Power Dissipation
It is possible to exceed the +150°C maximum junction
temperatures under certain load and power-supply
conditions. It is therefore important to calculate the
maximum junction temperature (T
to determine if power supply voltages, load conditions, or
package type need to be modified to remain in the safe
operating area. These parameters are related in Equation 4:
where:
• PD
• PD
where:
• T
• θ
• PD
• V
• I
• V
• R
T
PD
JMAX
FIGURE 65. GUARD RING EXAMPLE FOR UNITY GAIN
dissipation of each amplifier in the package (PD
Equation 5:
application
MAX
MAX
JA
MAX
S
OUTMAX
L
MAXTOTAL
MAX
MAX
= Load resistance
= Supply voltage (Magnitude of V
= Thermal resistance of the package
HIGH IMPEDANCE INPUT
=
= Maximum supply current of 1 amplifier
=
= Maximum ambient temperature
IN
T
for each amplifier can be calculated as shown in
= Maximum power dissipation of 1 amplifier
2*V
MAX
= Maximum output voltage swing of the
AMPLIFIER
S
+
×
is the sum of the maximum power
(
I
θ
SMAX
JA
xPD
+
MAXTOTAL
(
V
S
- V
OUTMAX
JMAX
V+
)
+
) for all applications
1/2 ISL28274
1/4 ISL28474
and V
)
×
V
--------------------------- -
OUTMAX
-
)
R
L
MAX
May 14, 2009
(EQ. 5)
(EQ. 4)
FN6345.3
)