MCP6272-E/SN Microchip Technology, MCP6272-E/SN Datasheet - Page 18

• Manufacturer Part Number: MCP6272-E/SN
• Description: IC OPAMP 2.0V DUAL R-R 8SOIC
• Manufacturer: Microchip Technology

Specifications of MCP6272-E/SN

• Slew Rate: 0.9 V/µs
• Package / Case: 8-SOIC (3.9mm Width)
• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 2MHz
• Current - Input Bias: 1pA
• Voltage - Input Offset: 3000µV
• Current - Supply: 170µA
• Current - Output / Channel: 25mA
• Voltage - Supply, Single/dual (±): 2 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Number Of Channels: 2
• Common Mode Rejection Ratio (min): 70 dB
• Input Offset Voltage: 3 mV
• Input Bias Current (max): 1 pA
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Shutdown: No
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Technology: CMOS
• Voltage Gain Db: 110 dB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP6271/1R/2/3/4/5
4.9.3.5
Figure 4-14
pass filter with Chip Select. Use the FilterLab
from Microchip Technology Inc. to determine the R and
C values for op amp A’s second order filter. Op amp B
can be used to add a pole-zero pair using C
R
FIGURE 4-14:
Feedback Low-Pass Filter with an Extra Pole-
Zero Pair.
4.9.3.6
Figure 4-15
filter with Chip Select. Use the Filterlab
Microchip to determine the R and C values for
op amp A’s second order filter. Op amp B can be used
to add a pole-zero pair using C
FIGURE 4-15:
Low-Pass Filter with an Extra Pole-Zero Pair and
Chip Select.
DS21810F-page 18
V
7
V
.
IN
IN
R
4
V
R
DD
3
is a second order multiple feedback low-
is a second order Sallen-Key low-pass
C
Second Order MFB with an Extra
Pole-Zero Pair
Second Order Sallen-Key with an
Extra Pole-Zero Pair
R
R
2
2
R
3
R
R
5
2
4
C
R
A
1
Second Order Multiple
Second Order Sallen-Key
1
R
C
A
1
1
MCP6275
R
MCP6275
3
6
R
, R
CS
5
CS
5
and R
C
R
B
®
3
7
C
R
B
software from
3
6
6
.
®
3
software
, R
V
V
6
OUT
OUT
and
4.9.3.7
The low-pass filter shown in
require external capacitors and uses only three
external resistors; the op amp’s GBWP sets the corner
frequency. R
is used to set the Q. To avoid gain peaking in the
frequency response, Q needs to be low (lower values
need to be selected for R
bandwidth varies greatly over temperature and
process. This configuration, however, provides a low
cost solution for applications with high bandwidth
requirements.
FIGURE 4-16:
Low-Pass Filter with Chip Select.
V
V
IN
REF
R
1
Capacitorless Second Order
Low-Pass filter with Chip Select
2
and R
2
A
are used to set the circuit gain. R
Capacitorless Second Order
© 2008 Microchip Technology Inc.
MCP6275
R
3
3
CS
). Note that the amplifier
Figure 4-16
R
B
1
V
does not
OUT
3