LT1637HS8#TR Linear Technology, LT1637HS8#TR Datasheet - Page 11
![IC OPAMP R-R IN/OUT 1.1MHZ 8SOIC](/photos/12/47/124722/lt1637hs8_pbf_sml.jpg)
LT1637HS8#TR
Manufacturer Part Number
LT1637HS8#TR
Description
IC OPAMP R-R IN/OUT 1.1MHZ 8SOIC
Manufacturer
Linear Technology
Series
Over-The-Top®r
Datasheet
1.LT1637CS8PBF.pdf
(16 pages)
Specifications of LT1637HS8#TR
Amplifier Type
General Purpose
Number Of Circuits
1
Output Type
Rail-to-Rail
Slew Rate
0.4 V/µs
Gain Bandwidth Product
1.1MHz
Current - Input Bias
17nA
Voltage - Input Offset
100µV
Current - Supply
230µA
Current - Output / Channel
31.7mA
Voltage - Supply, Single/dual (±)
2.7 V ~ 44 V, ±1.35 V ~ 22 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
-3db Bandwidth
-
Other names
LT1637HS8TR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
Supply Voltage
The positive supply pin of the LT1637 should be bypassed
with a small capacitor (about 0.01µF) within an inch of the
pin. When driving heavy loads an additional 4.7µF electro-
lytic capacitor should be used. When using split supplies,
the same is true for the negative supply pin.
The LT1637 is protected against reverse battery voltages
up to 25V. In the event a reverse battery condition occurs,
the supply current is typically less than 1nA.
When operating the LT1637 on total supplies of 30V or
more, the supply must not be brought up faster than 1µs.
This is especially true if low ESR bypass capacitors are
used. A series RLC circuit is formed from the supply lead
inductance and the bypass capacitor. 5Ω of resistance in
the supply or the bypass capacitor will dampen the tuned
circuit enough to limit the rise time.
Inputs
The LT1637 has two input stages, NPN and PNP (see the
Simplified Schematic), resulting in three distinct operat-
ing regions as shown in the Input Bias Current vs Common
Mode typical performance curve.
For input voltages about 0.9V or more below V
input stage is active and the input bias current is typically
– 20nA. When the input voltage is about 0.5V or less from
V
current is typically 80nA. Increases in temperature will
cause the voltage at which operation switches from the
PNP stage to the NPN stage to move towards V
offset voltage of the NPN stage is untrimmed and is
typically 600µV.
A Schottky diode in the collector of each NPN transistor of
the NPN input stage allows the LT1637 to operate with
either or both of its inputs above V
V
bias current is typically 23µA at room temperature. The
input offset voltage is typically 600µV when operating
above V
V
+
+
–
, the NPN input stage is operating and the input bias
the NPN input transistor is fully saturated and the input
regardless of V
+
. The LT1637 will operate with its input 44V above
+
U
.
U
+
. At about 0.3V above
W
+
+
. The input
U
, the PNP
The inputs are protected against excursions as much as
22V below V
each input and a diode from the input to the negative
supply. There is no output phase reversal for inputs up to
5V below V
inputs and the maximum differential input voltage is 44V.
Output
The output voltage swing of the LT1637 is affected by
input overdrive as shown in the typical performance
curves. When monitoring input voltages within 100mV of
V
The output of the LT1637 can be pulled up to 25V beyond
V
is less than 0.5V.
The normally reverse biased substrate diode from the
output to V
output is forced below V
limited to 100mA, no damage will occur.
The LT1637 is internally compensated to drive at least
200pF of capacitance under any output loading condi-
tions. A 0.22µF capacitor in series with a 150Ω resistor
between the output and ground will compensate these
amplifiers for larger capacitive loads, up to 4700pF, at all
output currents.
Distortion
There are two main contributors of distortion in op amps:
output crossover distortion as the output transitions from
sourcing to sinking current and distortion caused by
nonlinear common mode rejection. Of course, if the op
amp is operating inverting there is no common mode
induced distortion. When the LT1637 switches between
input stages there is significant nonlinearity in the CMRR.
Lower load resistance increases the output crossover
distortion, but has no effect on the input stage transition
distortion. For lowest distortion the LT1637 should be
operated single supply, with the output always sourcing
current and with the input voltage swing between ground
and (V
istics curves.
+
+
, gain should be taken to keep the output from clipping.
with less than 1nA of leakage current, provided that V
+
– 0.9V). See the Typical Performance Character-
–
–
will cause unlimited currents to flow when the
. There are no clamping diodes between the
–
by an internal 1.3k resistor in series with
–
. If the current is transient and
LT1637
11
1637fd
+