AD8017AR-REEL Analog Devices Inc, AD8017AR-REEL Datasheet - Page 14
![IC AMP GP DUAL LP LDIST 8SOIC](/photos/5/66/56684/505-8-soic_sml.jpg)
AD8017AR-REEL
Manufacturer Part Number
AD8017AR-REEL
Description
IC AMP GP DUAL LP LDIST 8SOIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD8017AR-EVAL.pdf
(16 pages)
Specifications of AD8017AR-REEL
Rohs Status
RoHS non-compliant
Amplifier Type
General Purpose
Number Of Circuits
2
Slew Rate
1600 V/µs
-3db Bandwidth
160MHz
Current - Input Bias
16µA
Voltage - Input Offset
1800µV
Current - Supply
7mA
Current - Output / Channel
270mA
Voltage - Supply, Single/dual (±)
4.4 V ~ 12 V, ±2.2 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Power Supply Requirement
Single/Dual
Package Type
SOIC N
Pin Count
8
For Use With
AD8017AR-EVAL - BOARD EVAL FOR AD8017
Output Type
-
Gain Bandwidth Product
-
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
AD8017
The first technique for maximum heat sinking is to use a heavy
layer of copper. 2 oz. copper will provide better heat sinking
than 1 oz. copper. Additional internal circuit layers can also be
used to more effectively remove heat, and to provide better
power and ground distribution.
There are no “ground” pins per se on the AD8017 (when run
on a dual supply), but the power supplies (Pins 4 and 8) are at
ac ground. Thus, these pins can be safely tied to a maximum
area of copper foil without affecting the ac performance of the
part. On the surface side of the board, the copper area that
connects to Pins 4 and 8 should be enlarged and spread out to
the maximum extent possible. As a practical matter, there will
be diminishing returns from adding copper more than a few
centimeters from the pins.
When the power supplies are run on the board on internal
power planes, then these should also be made as large as practi-
cal, and multiple vias (~0.012 in. or 0.3 mm) should be provided
from the component layer near the power supply pins of the
AD8017 to the inner layers. These vias should not have any of
the traditional “thermal relief” spokes to the planes, because the
function of these is to impede heat flow for ease of soldering.
This is counter to the effect desired for heat sinking.
On the side of the board opposite the component, additional
heat sinking can be provided by adding copper area near the vias
to further lower the thermal resistance. Additional vias can be
provided throughout to better conduct heat from the inner layers
to the outer layers.
The remainder of the device pins are active signal pins and must
be treated a bit more carefully. Pins 2 and 6 are the summing
junctions of the op amps and will be the most adversely affected by
stray capacitance. For this reason, the copper area of these pins
should be minimized. In addition, the copper nearby on the
component layer should be kept more than 3 mm–5 mm away
from these pins, where possible. The inner and opposite side
circuit layers directly below the summing junctions should also
be void of copper.
The positive inputs and outputs can withstand somewhat more
capacitance than the summing junctions without adversely
affecting ac performance. However, these pins should be treated
carefully, and the amount of heat sinking and excess capacitance
should be analyzed and adjusted depending on the application.
If maximum ac performance is desired and the power dissipa-
tion is not extreme, then the copper area connected to these pins
should be minimized. If the ac performance is not very critical
and maximum power must be dissipated, then the copper area
connected to these pins can be increased. As in many other
areas of analog design, the designer must use some judgment
based on the consideration of the above, in order to produce a
satisfactory design.
LAYOUT CONSIDERATIONS
The specified high speed performance of the AD8017 requires
careful attention to board layout and component selection.
Table II shows recommended component values for the AD8017
and Figures 10–12 show recommended layouts for the 8-lead
SOIC package for a positive gain. Proper RF design techniques
and low parasitic component selections are mandatory.
Gain
–1
+1
+2
+10
R
The PCB should have a ground plane covering all unused
portions of the component side of the board to provide a low
impedance ground path. The ground plane should be removed
from the area near the input pins to reduce stray capacitance.
Chip capacitors should be used for supply bypassing (see Fig-
ures 4 and 5). One end should be connected to the ground
plane and the other within 1/8 in. of each power pin. An addi-
tional (4.7 µF–10 µF) tantalum electrolytic capacitor should be
connected in parallel.
The feedback resistor should be located close to the inverting
input pin in order to keep the stray capacitance at this node to
input will significantly affect high speed performance when
operating at low noninverting gain.
a minimum. Capacitance greater than 1.5 pF at the inverting
T
chosen for 50 Ω characteristic input impedance.
Table II. Typical Bandwidth vs. Gain Setting Resistors
(V
S
= 6 V, R
R
619
619
619
619
F
( )
L
= 100
R
619
619
68.8
G
( )
)
R
54.5
49.9
49.9
49.9
T
( )
Small Signal
–3 dB BW (MHz)
110
320
160
40