OP727ARUZ Analog Devices Inc, OP727ARUZ Datasheet - Page 11

• Manufacturer Part Number: OP727ARUZ
• Description: IC OPAMP GP R-R 700KHZ 8TSSOP
• Manufacturer: Analog Devices Inc
• Type: General Purpose Amplifierr

Specifications of OP727ARUZ

• Slew Rate: 0.2 V/µs
• Amplifier Type: General Purpose
• Number Of Circuits: 2
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 700kHz
• Current - Input Bias: 5nA
• Voltage - Input Offset: 30µV
• Current - Supply: 320µA
• Current - Output / Channel: 30mA
• Voltage - Supply, Single/dual (±): 2.7 V ~ 30 V, ±1.35 V ~ 15 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP
• Op Amp Type: Precision
• No. Of Amplifiers: 2
• Bandwidth: 700kHz
• Supply Voltage Range: 2.7V To 30V
• Amplifier Case Style: TSSOP
• No. Of Pins: 8
• Rail/rail I/o Type: Rail to Rail Output
• Number Of Elements: 2
• Unity Gain Bandwidth Product: 0.7MHz
• Common Mode Rejection Ratio: 104dB
• Input Offset Voltage: 300uV
• Input Bias Current: 11nA
• Single Supply Voltage (typ): 3/5/9/12/15/18/24/28V
• Dual Supply Voltage (typ): ±3/±5/±9/±12V
• Voltage Gain In Db: 113.98dB
• Power Supply Rejection Ratio: 120dB
• Power Supply Requirement: Single/Dual
• Shut Down Feature: No
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 30V
• Dual Supply Voltage (min): ±1.35V
• Dual Supply Voltage (max): ±15V
• Technology: BiCMOS
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Compliant

Input Over Voltage Protection
When the input of an amplifier is more than a diode drop below
V
(V–) or the positive supply (V+), respectively, to the input pins
which can destroy the device. In the case of OP777/OP727/
OP747, differential voltages equal to the supply voltage will not
cause any problem (see Figure 3). OP777/OP727/OP747 has
built- in 500 Ω internal current limiting resistors, in series with the
inputs, to minimize the chances of damage. It is a good practice to
keep the current flowing into the inputs below 5 mA. In this con-
text it should also be noted that the high breakdown of the input
transistors removes the necessity for clamp diodes between the
inputs of the amplifier, a feature that is mandatory on many preci-
sion op amps. Unfortunately, such clamp diodes greatly interfere
with many application circuits such as precision rectifiers and
comparators. The OP777/OP727/OP747 series is free from such
limitations.
Phase Reversal
Many amplifiers misbehave when one or both of the inputs are
forced beyond the input common-mode voltage range. Phase
reversal is typified by the transfer function of the amplifier effectively
reversing its transfer polarity. In some cases this can cause lockup in
servo systems and may cause permanent damage or nonrecoverable
parameter shifts to the amplifier. Many amplifiers feature compensa-
tion circuitry to combat these effects, but some are only effective for
the inverting input. Additionally, many of these schemes only work
for a few hundred millivolts or so beyond the supply rails. OP777/
OP727/OP747 has a protection circuit against phase reversal
when one or both inputs are forced beyond their input common-
mode voltage range. It is not recommended that the parts be
continuously driven more than 3 V beyond the rails.
REV. C
EE
Figure 3b. Input Voltage Can Exceed the Supply Voltage
Without Damage
, or above V
Figure 3a. Unity Gain Follower
CC
V p-p = 32V
, large currents will flow from the substrate
V
IN
TIME – 400 s/DIV
30V
V
OP777/
OP727/
OP747
SY
V
OUT
=
15V
–11–
Output Stage
The CMOS output stage has excellent (and fairly symmetric) output
drive and with light loads can actually swing to within 1 mV of both
supply rails. This is considerably better than similar amplifiers
featuring (so-called) rail-to-rail bipolar output stages. OP777/
OP727/OP747 is stable in the voltage follower configuration and
responds to signals as low as 1 mV above ground in single supply
operation.
Output Short Circuit
The output of the OP777/OP727/OP747 series amplifier is protected
from damage against accidental shorts to either supply voltage,
provided that the maximum die temperature is not exceeded on a
long-term basis (see Absolute Maximum Rating section). Current of
up to 30 mA does not cause any damage.
A Low-Side Current Monitor
In the design of power supply control circuits, a great deal of design
effort is focused on ensuring a pass transistor’s long-term reliability
over a wide range of load current conditions. As a result, monitoring
Figure 6. Rail-to-Rail Operation
V
IN
Figure 4. No Phase Reversal
= 1mV
Figure 5. Follower Circuit
TIME – 10 s/DIV
OP777/OP727/OP747
V
IN
TIME – 400 s/DIV
2.7V TO 30V
OP777/
OP727/
OP747
V
SY
V
V
OUT
OUT
=
= 1mV
15V
1.0mV