MAX16048ETN+ Maxim Integrated Products, MAX16048ETN+ Datasheet - Page 48

• Manufacturer Part Number: MAX16048ETN+
• Description: IC EE-PROG SYS MGR 8CH 56-TQFN
• Manufacturer: Maxim Integrated Products
• Type: System Managerr

Specifications of MAX16048ETN+

• Number Of Voltages Monitored: 8
• Output: Open Drain, Push-Pull
• Reset: Active Low
• Reset Timeout: Adjustable/Selectable
• Voltage - Threshold: Adjustable/Selectable
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 56-TQFN
• Manual Reset: Resettable
• Watchdog: Yes
• Supply Voltage (max): 14 V
• Supply Voltage (min): 3 V
• Supply Current (typ): 6500 uA
• Maximum Power Dissipation: 3810 mW
• Mounting Style: SMD/SMT
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

When r4Dh[3] is ‘1’ the watchdog timer operates in the
independent mode. In the independent mode, the
watchdog timer operates as if it were a separate chip.
The watchdog timer is activated immediately upon V
exceeding UVLO and once the boot-up sequence is
finished. If RESET is asserted by the sequencer state
machine, the watchdog timer and WDO will not be
affected.
There will be a long startup delay if r55h[6] is a ‘1.’ If
r55h[6] is a ‘0,’ there will not be a long startup delay.
In independent mode, if the Watchdog Reset Output
Enable bit r55h[7] is set to ‘1,’ when the watchdog timer
expires, WDO will be asserted then RESET will be
asserted. WDO will then be deasserted. WDO will be
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
Table 30. Miscellaneous Settings
48
REGISTER/
ADDRESS
______________________________________________________________________________________
EEPROM
5Ch
5Dh
65h
Independent Watchdog Timer Operation
BIT RANGE
[7:0]
[7:2]
[2:0]
[7:3]
[0]
[1]
User identification. Eight bits of memory for user-defined identification.
Configuration Lock
0 = Configuration registers and EEPROM writable.
1 = Configuration registers and EEPROM [except r5Dh] locked.
EEPROM Fault Data Lock Flag (set automatically after fault log is triggered):
0 = EEPROM is not locked. A triggered fault log stores fault information to EEPROM.
1 = EEPROM addresses 00h to 11h are locked. Write a ‘1’ to this bit to toggle the flag.
Not used
Manufacturing revision code. This register is read only. Not stored in EEPROM.
Not used
CC
low for 3 system clock cycles or approximately 1µs. If
the Watchdog Reset Output Enable bit (r55h[7]) is set
to ‘0,’ when the WDT expires, WDO will be asserted but
RESET will not be affected.
Table 30 lists several miscellaneous programmable
items. Register r5Ch provides storage space for a user-
defined configuration or firmware version number. Bit
r5Dh[0] locks and unlocks the configuration registers.
Bit r5Dh[1] locks and unlocks EEPROM addresses 00h
to 11h. Write data to EEPROM r5Dh as normally done;
however, to toggle a bit in register r5Dh, write a ‘1’ to
that bit. The r65h[2:0] bits contain a read-only manufac-
turing revision code.
DESCRIPTION
Miscellaneous