MAX16048ETN+ Maxim Integrated Products, MAX16048ETN+ Datasheet - Page 52
![IC EE-PROG SYS MGR 8CH 56-TQFN](/photos/6/50/65031/56-tqfn_21-0135f_sml.jpg)
MAX16048ETN+
Manufacturer Part Number
MAX16048ETN+
Description
IC EE-PROG SYS MGR 8CH 56-TQFN
Manufacturer
Maxim Integrated Products
Type
System Managerr
Datasheet
1.MAX16046EVKIT.pdf
(70 pages)
Specifications of MAX16048ETN+
Number Of Voltages Monitored
8
Output
Open Drain, Push-Pull
Reset
Active Low
Reset Timeout
Adjustable/Selectable
Voltage - Threshold
Adjustable/Selectable
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
56-TQFN
Manual Reset
Resettable
Watchdog
Yes
Supply Voltage (max)
14 V
Supply Voltage (min)
3 V
Supply Current (typ)
6500 uA
Maximum Power Dissipation
3810 mW
Mounting Style
SMD/SMT
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
12-Channel/8-Channel EEPROM-Programmable
System Managers with Nonvolatile Fault Registers
The MAX16046/MAX16048 use eight command codes
for block read, block write, and other commands. See
Table 32 for a list of command codes.
To initiate a software reboot, send 96h using the send
byte format. A software-initiated reboot is functionally the
same as a hardware-initiated power-on reset. During
boot-up, EEPROM configuration data in the range of 0Fh
to 7Dh is copied to the same register addresses in the
default page.
Send command code 97h to trigger a fault store to
EEPROM. Configure the Critical Fault Log Control register
(r47h) to store ADC conversion results and/or fault flags
in registers once the command code has been sent.
Using command code 98h allows access to the extend-
ed page, which contains registers for ADC conversion
results, DACOUT enables, and GPIO input/output data.
Use command code 99h to return to the default page.
Send command code 9Ah to access the EEPROM
page. Once command code 9Ah has been sent, all
addresses are recognized as EEPROM addresses only.
Send command code 9Bh to return to the default page.
When accessing any EEPROM location using a read
byte or block read protocol, set the address to the
desired location, send a dummy read byte protocol,
and then set the address to the desired location again.
This primes the device for subsequent read operations.
Table 32. Command Codes
The block write protocol (see Figure 12) allows the
master device to write a block of data (1 byte to 16
bytes) to memory. The destination address should be
preloaded by a previous send byte command; other-
wise the block write command begins to write at the
current address pointer. After the last byte is written,
the address pointer remains preset to the next valid
address. If the number of bytes to be written causes
52
COMMAND CODE
______________________________________________________________________________________
9Ah
9Bh
94h
95h
96h
97h
98h
99h
Write block
Read block
Reboot EEPROM in register file
Trigger fault store to EEPROM
Extended page access on
Extended page access off
EEPROM page access on
EEPROM page access off
ACTION
Command Codes
Block Write
the address pointer to exceed FFh for EEPROM or 7Dh
for configuration registers, the address pointer stays at
FFh or 7Dh, overwriting this memory address with the
remaining bytes of data. The last data byte sent is
stored at register address FFh. The slave generates a
NACK at step 5 if the command code is invalid or if the
device is busy, and the address pointer is not altered.
The block write procedure is the following:
1) The master sends a START condition.
2) The master sends the 7-bit slave address and a
3) The addressed slave asserts an ACK on SDA.
4) The master sends the 8-bit command code for
5) The addressed slave asserts an ACK on SDA.
6) The master sends the 8-bit byte count (1 byte to 16
7) The addressed slave asserts an ACK on SDA.
8) The master sends 8 bits of data.
9) The addressed slave asserts an ACK on SDA.
10) Repeat steps 8 and 9 n - 1 times.
11) The master sends a STOP condition.
The block read protocol (see Figure 12) allows the
master device to read a block of up to 16 bytes from
memory. Read fewer than 16 bytes of data by issuing
an early STOP condition from the master, or by gener-
ating a NACK with the master. The destination address
should be preloaded by a previous send byte com-
mand; otherwise the block read command begins to
read at the current address pointer. If the number of
bytes to be read causes the address pointer to exceed
FFh for the configuration register or EEPROM, the
address pointer stays at FFh and the last data byte
read is from register rFFh. The block read procedure is
the following:
1) The master sends a START condition.
2) The master sends the 7-bit slave address and a
3) The addressed slave asserts an ACK on SDA.
4) The master sends 8 bits of the block read com-
5) The slave asserts an ACK on SDA, unless busy.
6) The master generates a REPEATED START condition.
7) The master sends the 7-bit slave address and a
write bit (low).
block write (94h).
bytes), n .
write bit (low).
mand (95h).
read bit (high).
Block Read