X5323S8I-4.5AT1 Intersil, X5323S8I-4.5AT1 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
X5323S8I-4.5AT1
Manufacturer Part Number
X5323S8I-4.5AT1
Description
IC SUPERVISOR CPU 32K EE 8-SOIC
Manufacturer
Intersil
Type
Simple Reset/Power-On Resetr
Datasheet
1.X5323S8IZT1.pdf
(20 pages)
Specifications of X5323S8I-4.5AT1
Number Of Voltages Monitored
1
Output
Open Drain or Open Collector
Reset
Active Low
Reset Timeout
100 ms Minimum
Voltage - Threshold
4.63V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
When the highest address is reached, the address counter
rolls over to address $0000 allowing the read cycle to be
continued indefinitely. The read operation is terminated by
taking CS high. Refer to the read EEPROM Array Sequence
(Figure 1).
To read the status register, the CS line is first pulled low to
select the device followed by the 8-bit RDSR instruction.
After the RDSR opcode is sent, the contents of the status
register are shifted out on the SO line. Refer to the read
status register sequence (Figure 2).
Write Sequence
Prior to any attempt to write data into the device, the “Write
Enable” Latch (WEL) must first be set by issuing the WREN
instruction (Figure 3). CS is first taken LOW, then the WREN
instruction is clocked into the device. After all eight bits of the
instruction are transmitted, CS must then be taken HIGH. If
the user continues the write operation without taking CS
HIGH after issuing the WREN instruction, the write operation
will be ignored.
To write data to the EEPROM memory array, the user then
issues the WRITE instruction followed by the 16-bit address
and then the data to be written. Any unused address bits are
specified to be “0’s”. The WRITE operation minimally takes
32 clocks. CS must go low and remain low for the duration of
the operation. If the address counter reaches the end of a
page and the clock continues, the counter will roll back to the
first address of the page and overwrite any data that may
have been previously written.
Note: When writing more than one page, you must wait one
write cycle (10ms typical) when going from one page to
another. This is required for the internal nonvolatile memory
to be programmed correctly.
SCK
CS
SO
SI
9
HIGH IMPEDANCE
0
1
INSTRUCTION
FIGURE 6. READ STATUS REGISTER SEQUENCE
2
3
4
X5323, X5325
5
6
7
MSB
8
7
For the page write operation (byte or page write) to be
completed, CS can only be brought HIGH after bit 0 of the
last data byte to be written is clocked in. If it is brought HIGH
at any other time, the write operation will not be completed
(Figure 4).
To write to the status register, the WRSR instruction is
followed by the data to be written (Figure 5). Data bits 0 and
1 must be “0”.
While the write is in progress following a status register or
EEPROM Sequence, the status register may be read to
check the WIP bit. During this time the WIP bit will be high.
Operational Notes
The device powers-up in the following state:
• The device is in the low power standby state.
• A HIGH to LOW transition on CS is required to enter an
• SO pin is high impedance.
• The write enable latch is reset.
• The flag bit is reset.
• Reset signal is active for t
Data Protection
The following circuitry has been included to prevent
inadvertent writes:
• A WREN instruction must be issued to set the write enable
• CS must come HIGH at the proper clock count in order to
active state and receive an instruction.
latch.
start a nonvolatile write cycle.
9
6
10
5
DATA OUT
11 12
4
3
13
2
14
1
0
PURST
.
June 30, 2008
FN8131.2